Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

Concrete and wood coffee table + (Unscrew the formwork and scrap off any of the caulk that is stuck to the concrete.)
Concrete and wood coffee table + (Unscrew the formwork and scrap off any of the caulk that is stuck to the concrete.)

Le cyclo chargeur + (Le cyclo-chargeur convertit l’énergie méca … Le cyclo-chargeur convertit l’énergie mécanique fournie par le pédalage en énergie électrique. La roue entraîne un galet qui fait tourner un moteur DC utilisé comme génératrice. Le courant produit est ensuite redressé par une diode, puis stabilisé par un régulateur de tension avant d’être utilisé pour alimenter des appareils électriques. pour alimenter des appareils électriques.)
Replace brake handle Xiaomi Mi elesctric scooter + (Begin by releasing the brake cable from th … Begin by releasing the brake cable from the lever. Pull the red brake outer tube away from the lever to reveal the metal ferrule, then pull the cable away from the front of the scooter allowing it to pass through the channel in the front of the lever. Once free you can depress the lever to reveal the round metal head of the cable, lift it up to release it from the handle. lift it up to release it from the handle.)
Bucket stool made of wood and concrete + (Bend the sides of the bucket outwards a few times in each direction to loosen the concrete; then pull the stool out by the legs.)
Bucket stool made of wood and concrete + (Bend the sides of the bucket outwards a few times in each direction to loosen the concrete; then pull the stool out by the legs.)
Spinning Kinetic Sculpture RGB + (Cut the first svg file on 2 sheets of 300c … Cut the first svg file on 2 sheets of 300cmx300xm [[:Fichier:DecoupePart1.svg|DecoupePart1.svg]]. Do the same for the second file [[:Fichier:DecoupePart2.svg|DecoupePart2.svg]]. The cutting file is about 300cm by 300cm so if you have a 600x300 you can cut them two by two by merging the files. Bring together similar pieces so it's easier to work.her similar pieces so it's easier to work.)
SolarOSE - Guide 7: Assembling of the receiver + (Cut the squared tube at a length of 2.2 m. Put the 10 hangers on the squared tube, with a spacing of 22 cm.)
MicroHouse + (Download on our [https://github.com/wikiho … Download on our [https://github.com/wikihouseproject/Microhouse/ Github repo] the set of milling drawings which can be used by CNC cutter to fabricate the house parts. Cut the part by a CNC mill using locally bought material. This is 18mm plywood, in the standard sheet size of 2440mm x 1220mm (8' x 4') Each component can be combined or adapted to form a structure which responds to an individual site or set of needs.nds to an individual site or set of needs.)
TOLOU SENFABLAB + ( * Fer à souder + étain * Pistolet à colle * Multimètre * Pince coupante * Imprimante 3D )
Recycled Plastic Products + (Making products out of recycled plastic caps, it is very important to ensure that all contaminants have been removed for a better quality.)
ZipStich Chair with plywood pieces and zip ties + (Measure and mark the plywood with a pencil.)
ZipStich Chair with plywood pieces and zip ties + (Measure and mark the plywood with a pencil.)
Desk lamp in wood and concrete + (Put a mark on the batten, to cut it in 2 battens of 44cm length)
Desk lamp in wood and concrete + (Put a mark on the batten, to cut it in 2 battens of 44cm length)
Marble Machine No 1 Motor Assembly Instructions + (The parts can be glued together in one go … The parts can be glued together in one go and the parts held in place with rubber bands The bottom '''should not '''be glued but can be used to hold parts aligned while the glue dries. The bottom is left loose for access to switch and batteries. If you don't want the text to be visible, simply turn the part so it face inwards. When viewed from the front the holes for the motor mount (circled in red) should face left as shown in the picture below.d face left as shown in the picture below.)
PiKon telescope + (The PiKon telescope is a robust design but … The PiKon telescope is a robust design but there are two issues that need care if you are to get the most out of your project. '''Dust and the Camera Sensor''' PiKon benefits from a very simple design that has just one optical component. The lens of the Raspberry Pi Camera is removed to allow imaging by the Optical Mirror. This means that the Raspberry Pi Camera sensor is exposed to dust and dirt. Adding sensor protection would add two optical surfaces to the design, so the sensor is left exposed. This is not a problem provided care is taken to avoid dust and dirt getting on the sensor. '''Care of the Mirror''' As with all reflecting telescopes, care must be taken to avoid damaging the mirror. When assembling or modifying the telescope be careful not to let components drop down the Telescope Tube onto the Mirror.p down the Telescope Tube onto the Mirror.)
Concrete and wood coffee table + (Use a circular saw to cut four balusters into 12” length pieces and another four balusters into 18” length pieces.)
Concrete and wood coffee table + (Use a circular saw to cut four balusters into 12” length pieces and another four balusters into 18” length pieces.)
Glowing LED Butterfly + (Use TinkerCad to design the component that … Use TinkerCad to design the component that will be 3D printed. This is a great opportunity to develop your computer aided design (CAD) skills! What to think about.. - Needs to have holes for the light to go through - Needs to be big enough to hide the Arduino and PCB - Needs to be able to sit on the top of the 9V battery Pre-made butterfly design can be found through this linkrfly design can be found through this link)
Replace dashboard and bluetooth card Xiaomi electric scooter + (Using your nails or a plastic spudger, carefully lift the two plastic covers from the top of the stem. They are held on with foam tape so a hairdryer on a cool setting can warm the adhesive and aide the release if you are having difficulty.)
Escooterfix - Replace front LED lamp Xiaomi Mi electric scooter + (Using your nails or a plastic spudger, carefully lift the two plastic covers from the top of the stem. They are held on with foam tape so a hairdryer on a cool setting can warm the adhesive and aide the release if you are having difficulty.)
OpenKnit: digital fabrication tool to create your own clothes + (You'll need to thread: two 20x20x800 mm bars: 6 mm tool on both sides. two 30x30x800 mm bars: 8 mm tool on both sides. two 30x30x162 mm bars: 8 mm tool on ONE side, plus one 8 mm hole on the top (see image).)