Salad tongs : Différence entre versions

Version du 14 juin 2018 à 10:32

A nice set of wooden salad tongs.

Auteur Bob Clagett | Dernière modification 9/12/2019 par Clementflipo

Difficulté

Facile

Durée

4 heure(s)

Catégories

Alimentation & Agriculture, Mobilier

Coût

20 USD ($)

A nice set of wooden salad tongs.

Difficulté

Facile

Durée

4 heure(s)

Catégories

Alimentation & Agriculture, Mobilier

Coût

20 USD ($)

Autres langues :

English • ‎français

Sommaire

1 Introduction
2 Video d'introduction
3 Étape 1 - Cut down the rough wood
4 Étape 2 - Add the slot for the aluminum
5 Étape 3 - Shape the wooden handles
6 Étape 4 - Drilled out the holes
7 Étape 5 - Add the aluminum
8 Étape 6 - Drive in the dowels
9 Étape 7 - Finish with oil
10 Étape 8 - Now, To Find Some Salad!
11 Notes et références
12 Commentaires

Licence : Attribution (CC BY)

tongs, wood Salad_tongs_intro_logo.png en none Creation 0

Introduction

I made this simple pair of salad tongs for my wife, but we also wanted a geeky, over-the-top pair that looked like the Infinity Gauntlet (see the tutorial on Wikifab).

Video d'introduction

Matériaux

Block of basswood

Aluminium bar

Outils

Band saw

Table saw

Belt sander

Drill press

Torch and aluminium rode

Étape 1 - Cut down the rough wood

For the functional tongs, I use a large chunk of basswood. I drew out the spatula-like shape on the face and cut the thick piece of wood on the band saw. I then turned the piece on its side and resawed the basswood into my two handles. These two halves were still pretty thick and the shape was not yet finalized, all of that would be done with the sanders.

Étape 2 - Add the slot for the aluminum

Now here’s your word of warning, the cut I made into the stem of the handles made me a little nervous. In hindsight, I could have made a quick jig to securely hold the pieces while I passed them over the table saw vertically, but I didn’t think of that at the time. Instead, I mitigated all of the risks and carefully passed the skinny end of the handles over the blade to cut in the pocket that would hold the aluminum.

This ended up working just fine, but be careful.

Étape 3 - Shape the wooden handles

This process involved a lot of patience and a lot of sanding. I flushed up the stem edges with the edges of the aluminum and then used the belt sander to finalize the handles’ overall shape. The two handles were pressed together and sanded simultaneously so that their profiles matched. The scoop was carved into the paddles by running them over the rounded end of the belt sander. To round over the crisp edges, I clamped the handles to my work bench and used some files to make some comfortable contours.

Étape 4 - Drilled out the holes

For the handles, I used some flat aluminum bar stock that I could bend over to act as a spring. Before I bent the metal, I set the flat bar into the slots on the wooden handles and drilled out the holes for the dowels that would connect the pieces with the drill press. I had some 3/8″ aluminum round bar and cut little dowel pieces on the miter saw. Two holes were drilled through both materials so later, I could permanently peg them together.

Étape 5 - Add the aluminum

To bend the flat bar into a spring, I first scored a groove down the center of the piece to act as a fold line. I carefully heated up the aluminum along this line and hammered the piece over into an acute angle. There was an obvious cut line left in the crease that I wanted to cover up. So, I used a torch and some aluminum rod to braise the crease for some extra strength and to give the handles a cleaner look.

Étape 6 - Drive in the dowels

All that was left was to drive in the dowels (0,5cm high) through the attachment holes and secure them in place with some CA glue.

Étape 7 - Finish with oil

Because this piece will be touching food, I used a butcher block conditioner meant for cutting boards. This product is food safe and won’t leak any harmful chemicals into our healthy salads. I really like this oil because it’s quick and easy, leaves the wood a vibrant color, and I don’t have to worry about it coming in contact with the things we eat.

Étape 8 - Now, To Find Some Salad!

This project is done. I set out to make a functional set of salad tongs that we could use for dinner and I did that. But…a project this simple begs for a dash of nerd, so we went a little overboard and made something kind silly (awesome) using more outlandish tools.

A awesome idea : The Infinity Gauntlet Salad Tongs

Notes et références

Check out this tutoral and a many more on iliketomakestuff.com.

Subscribe to my channel: http://bit.ly/1k8msFr

Second Channel: http://bit.ly/iltms-2

MORE PROJECTS, POSTS AND EVENTS

http://www.iliketomakestuff.com

TOOLS & SUPPLIES (affiliate links):

https://kit.com/iliketomakestuff/infi...

https://kit.com/iliketomakestuff/shop...

Twitch Stream Every Wednesday @ 11am EST: www.twitch.tv/iliketomakestuff

I WROTE A BOOK!!

http://www.iliketomakestuff.com/makin...

Want to support ILTMS? Get exclusive content and more...

http://www.iliketomakestuff.com/patreon

BUY A SHIRT, STICKER, DIGITAL PLANS and MORE!!

http://www.iliketomakestuff.com/store

FOLLOW:

http://twitter.com/iliketomakestuf

http://www.twitch.tv/iliketomakestuff

http://instagram.com/iliketomakestuff

http://facebook.com/iltms

Commentaires

Yes

@@ Ligne 3 : / Ligne 3 : @@
 |Area=Food and Agriculture, Furniture
 |Tags=tongs, wood
-|Description=<translate>A nice set of wooden salad tongs.</translate>
+|Description=<translate><!--T:1--> A nice set of wooden salad tongs.</translate>
 |Difficulty=Easy
 |Cost=20
@@ Ligne 16 : / Ligne 16 : @@
 }}
 {{ {{tntn|Introduction}}
-|Introduction=<translate>I made this simple pair of salad tongs for my wife, but we also wanted a geeky, over-the-top pair that looked like the Infinity Gauntlet ([[Infinity Gauntlet Salad Tongs|see the tutorial on Wikifab]]).</translate>
+|Introduction=<translate><!--T:2--> I made this simple pair of salad tongs for my wife, but we also wanted a geeky, over-the-top pair that looked like the Infinity Gauntlet ([[Infinity Gauntlet Salad Tongs|see the tutorial on Wikifab]]).</translate>
 }}
 {{ {{tntn|TutoVideo}}
@@ Ligne 23 : / Ligne 23 : @@
 }}
 {{ {{tntn|Materials}}
-|Material=<translate>Block of basswood
+|Material=<translate><!--T:3-->
+Block of basswood
+<!--T:4-->
 Aluminium bar</translate>
-|Tools=<translate>Band saw
+|Tools=<translate><!--T:5-->
+Band saw
+<!--T:6-->
 Table saw
+<!--T:7-->
 Belt sander
+<!--T:8-->
 Drill press
+<!--T:9-->
 Torch and aluminium rode</translate>
 }}
@@ Ligne 44 : / Ligne 51 : @@
 |Step_Picture_03=Salad_tongs__tape_3c_retuch_big.png
 |Step_Picture_04=Salad_tongs__tape_3d_retuch.png
-|Step_Title=<translate>Cut down the rough wood</translate>
+|Step_Title=<translate><!--T:10--> Cut down the rough wood</translate>
-|Step_Content=<translate>For the functional tongs, I use a large chunk of basswood. I drew out the spatula-like shape on the face and cut the thick piece of wood on the band saw. I then turned the piece on its side and resawed the basswood into my two handles. These two halves were still pretty thick and the shape was not yet finalized, all of that would be done with the sanders.</translate>
+|Step_Content=<translate><!--T:11--> For the functional tongs, I use a large chunk of basswood. I drew out the spatula-like shape on the face and cut the thick piece of wood on the band saw. I then turned the piece on its side and resawed the basswood into my two handles. These two halves were still pretty thick and the shape was not yet finalized, all of that would be done with the sanders.</translate>
 }}
 {{ {{tntn|Tuto Step}}
 |Step_Picture_00=Salad_tongs__tape_2.png
 |Step_Picture_01=Salad_tongs__tape_2b_retuch_small.png
-|Step_Title=<translate>Add the slot for the aluminum</translate>
+|Step_Title=<translate><!--T:12--> Add the slot for the aluminum</translate>
-|Step_Content=<translate>Now here’s your word of warning, the cut I made into the stem of the handles made me a little nervous. In hindsight, I could have made a quick jig to securely hold the pieces while I passed them over the table saw vertically, but I didn’t think of that at the time. Instead, I mitigated all of the risks and carefully passed the skinny end of the handles over the blade to cut in the pocket that would hold the aluminum.
+|Step_Content=<translate><!--T:13-->
+Now here’s your word of warning, the cut I made into the stem of the handles made me a little nervous. In hindsight, I could have made a quick jig to securely hold the pieces while I passed them over the table saw vertically, but I didn’t think of that at the time. Instead, I mitigated all of the risks and carefully passed the skinny end of the handles over the blade to cut in the pocket that would hold the aluminum.
+<!--T:14-->
 {{Warning|This ended up working just fine, but be careful.}}</translate>
 }}
@@ Ligne 61 : / Ligne 70 : @@
 |Step_Picture_03=Salad_tongs_pretty_much_same_logo.png
 |Step_Picture_04=Salad_tongs_files_logo.png
-|Step_Title=<translate>Shape the wooden handles</translate>
+|Step_Title=<translate><!--T:15--> Shape the wooden handles</translate>
-|Step_Content=<translate>This process involved a lot of patience and a lot of sanding. I flushed up the stem edges with the edges of the aluminum and then used the belt sander to finalize the handles’ overall shape. The two handles were pressed together and sanded simultaneously so that their profiles matched. The scoop was carved into the paddles by running them over the rounded end of the belt sander. To round over the crisp edges, I clamped the handles to my work bench and used some files to make some comfortable contours.</translate>
+|Step_Content=<translate><!--T:16--> This process involved a lot of patience and a lot of sanding. I flushed up the stem edges with the edges of the aluminum and then used the belt sander to finalize the handles’ overall shape. The two handles were pressed together and sanded simultaneously so that their profiles matched. The scoop was carved into the paddles by running them over the rounded end of the belt sander. To round over the crisp edges, I clamped the handles to my work bench and used some files to make some comfortable contours.</translate>
 }}
 {{ {{tntn|Tuto Step}}
@@ Ligne 68 : / Ligne 77 : @@
 |Step_Picture_01=Salad_tongs_mesures_logo.png
 |Step_Picture_02=Salad_tongs_finilogo.png
-|Step_Title=<translate>Drilled out the holes</translate>
+|Step_Title=<translate><!--T:17--> Drilled out the holes</translate>
-|Step_Content=<translate>For the handles, I used some flat aluminum bar stock that I could bend over to act as a spring. Before I bent the metal, I set the flat bar into the slots on the wooden handles and drilled out the holes for the dowels that would connect the pieces with the drill press. I had some 3/8″ aluminum round bar and cut little dowel pieces on the miter saw. Two holes were drilled through both materials so later, I could permanently peg them together.</translate>
+|Step_Content=<translate><!--T:18--> For the handles, I used some flat aluminum bar stock that I could bend over to act as a spring. Before I bent the metal, I set the flat bar into the slots on the wooden handles and drilled out the holes for the dowels that would connect the pieces with the drill press. I had some 3/8″ aluminum round bar and cut little dowel pieces on the miter saw. Two holes were drilled through both materials so later, I could permanently peg them together.</translate>
 }}
 {{ {{tntn|Tuto Step}}
@@ Ligne 78 : / Ligne 87 : @@
 |Step_Picture_03=Salad_tongs_marteau_4.png
 |Step_Picture_04=Salad_tongs_fondu_5.png
-|Step_Title=<translate>Add the aluminum</translate>
+|Step_Title=<translate><!--T:19--> Add the aluminum</translate>
-|Step_Content=<translate>To bend the flat bar into a spring, I first scored a groove down the center of the piece to act as a fold line. I carefully heated up the aluminum along this line and hammered the piece over into an acute angle. There was an obvious cut line left in the crease that I wanted to cover up. So, I used a torch and some aluminum rod to braise the crease for some extra strength and to give the handles a cleaner look.</translate>
+|Step_Content=<translate><!--T:20--> To bend the flat bar into a spring, I first scored a groove down the center of the piece to act as a fold line. I carefully heated up the aluminum along this line and hammered the piece over into an acute angle. There was an obvious cut line left in the crease that I wanted to cover up. So, I used a torch and some aluminum rod to braise the crease for some extra strength and to give the handles a cleaner look.</translate>
 }}
 {{ {{tntn|Tuto Step}}
@@ Ligne 86 : / Ligne 95 : @@
 |Step_Picture_01_annotation={"objects":[{"type":"textbox","originX":"center","originY":"center","left":361,"top":213,"width":54.45,"height":22.6,"fill":"white","stroke":"white","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeLineJoin":"miter","strokeMiterLimit":10,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"0.5cm","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"","lineHeight":1.16,"textDecoration":"","textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{"0":{"1":{},"2":{},"3":{},"4":{},"5":{},"6":{},"7":{} } } },{"type":"wfarrow","originX":"center","originY":"center","left":326.31,"top":216.04,"width":10,"height":90,"fill":"rgba(255,0,0,0)","stroke":"white","strokeWidth":6,"strokeDashArray":null,"strokeLineCap":"butt","strokeLineJoin":"miter","strokeMiterLimit":10,"scaleX":0.5,"scaleY":0.5,"angle":177.63,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"points":[{"x":10,"y":10},{"x":10,"y":100},{"x":5,"y":90},{"x":10,"y":100},{"x":15,"y":90}]}],"height":"338","width":"600"}
 |Step_Picture_02=Salad_tongs_colle_logo.png
-|Step_Title=<translate>Drive in the dowels</translate>
+|Step_Title=<translate><!--T:21--> Drive in the dowels</translate>
-|Step_Content=<translate>All that was left was to drive in the dowels (0,5cm high) through the attachment holes and secure them in place with some CA glue.</translate>
+|Step_Content=<translate><!--T:22--> All that was left was to drive in the dowels (0,5cm high) through the attachment holes and secure them in place with some CA glue.</translate>
 }}
 {{ {{tntn|Tuto Step}}
@@ Ligne 94 : / Ligne 103 : @@
 |Step_Picture_02=Salad_tongs_huile_logo.png
 |Step_Picture_03=Salad_tongs_beau_logo.png
-|Step_Title=<translate>Finish with oil</translate>
+|Step_Title=<translate><!--T:23--> Finish with oil</translate>
-|Step_Content=<translate>Because this piece will be touching food, I used a butcher block conditioner meant for cutting boards. This product is food safe and won’t leak any harmful chemicals into our healthy salads. I really like this oil because it’s quick and easy, leaves the wood a vibrant color, and I don’t have to worry about it coming in contact with the things we eat.</translate>
+|Step_Content=<translate><!--T:24--> Because this piece will be touching food, I used a butcher block conditioner meant for cutting boards. This product is food safe and won’t leak any harmful chemicals into our healthy salads. I really like this oil because it’s quick and easy, leaves the wood a vibrant color, and I don’t have to worry about it coming in contact with the things we eat.</translate>
 }}
 {{ {{tntn|Tuto Step}}
 |Step_Picture_00=Salad_tongs_der_des_ders.png
-|Step_Title=<translate>Now, To Find Some Salad!</translate>
+|Step_Title=<translate><!--T:25--> Now, To Find Some Salad!</translate>
-|Step_Content=<translate>This project is done. I set out to make a functional set of salad tongs that we could use for dinner and I did that. But…a project this simple begs for a dash of nerd, so we went a little overboard and made something kind silly (awesome) using more outlandish tools.
+|Step_Content=<translate><!--T:26-->
+This project is done. I set out to make a functional set of salad tongs that we could use for dinner and I did that. But…a project this simple begs for a dash of nerd, so we went a little overboard and made something kind silly (awesome) using more outlandish tools.
+<!--T:27-->
 {{Idea|A awesome idea : [http://wikifab.org/wiki/Infinity_Gauntlet_Salad_Tongs&#124; The Infinity Gauntlet Salad Tongs]}}</translate>
 }}
 {{ {{tntn|Notes}}
-|Notes=<translate>Check out this tutoral and a many more on [https://www.iliketomakestuff.com/infinity-gauntlet-salad-tongs/ iliketomakestuff.com].
+|Notes=<translate><!--T:28-->
+Check out this tutoral and a many more on [https://www.iliketomakestuff.com/infinity-gauntlet-salad-tongs/ iliketomakestuff.com].
+<!--T:29-->
 Subscribe to my channel: [https://www.youtube.com/redirect?q=http%3A%2F%2Fbit.ly%2F1k8msFr&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://bit.ly/1k8msFr]
+<!--T:30-->
 Second Channel: [https://www.youtube.com/redirect?q=http%3A%2F%2Fbit.ly%2Filtms-2&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://bit.ly/iltms-2]
+<!--T:31-->
 MORE PROJECTS, POSTS AND EVENTS
+<!--T:32-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Fwww.iliketomakestuff.com&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://www.iliketomakestuff.com]
+<!--T:33-->
 TOOLS & SUPPLIES (affiliate links):
+<!--T:34-->
 [https://www.youtube.com/redirect?q=https%3A%2F%2Fkit.com%2Filiketomakestuff%2Finfinity-gauntlet-salad-tongs&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz https://kit.com/iliketomakestuff/infi...]
+<!--T:35-->
 [https://www.youtube.com/redirect?q=https%3A%2F%2Fkit.com%2Filiketomakestuff%2Fshop-safety-gear&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz https://kit.com/iliketomakestuff/shop...]
+<!--T:36-->
 Twitch Stream Every Wednesday @ 11am EST: www.twitch.tv/iliketomakestuff
+<!--T:37-->
 I WROTE A BOOK!!
+<!--T:38-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Fwww.iliketomakestuff.com%2Fmakingtime&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://www.iliketomakestuff.com/makin...]
+<!--T:39-->
 Want to support ILTMS? Get exclusive content and more...
+<!--T:40-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Fwww.iliketomakestuff.com%2Fpatreon&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://www.iliketomakestuff.com/patreon]
+<!--T:41-->
 BUY A SHIRT, STICKER, DIGITAL PLANS and MORE!!
+<!--T:42-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Fwww.iliketomakestuff.com%2Fstore&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://www.iliketomakestuff.com/store]
+<!--T:43-->
 FOLLOW:
+<!--T:44-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Ftwitter.com%2Filiketomakestuf&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://twitter.com/iliketomakestuf]
+<!--T:45-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Fwww.twitch.tv%2Filiketomakestuff&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://www.twitch.tv/iliketomakestuff]
+<!--T:46-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Finstagram.com%2Filiketomakestuff&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://instagram.com/iliketomakestuff]
+<!--T:47-->
 [https://www.youtube.com/redirect?q=http%3A%2F%2Ffacebook.com%2Filtms&v=EKh4onHwuGI&event=video_description&redir_token=flG2NNhf13dFt3Z19Ai6kgqiKAx8MTUyODk4NTQ4M0AxNTI4ODk5MDgz http://facebook.com/iltms]</translate>
 }}