(set pageLanguageSource property) |
(update property name) |
||
Ligne 1 : | Ligne 1 : | ||
− | {{ | + | {{Tuto Details |
|SourceLanguage=none | |SourceLanguage=none | ||
|Language=en | |Language=en | ||
Ligne 14 : | Ligne 14 : | ||
|Main_Picture=SolarOSE_G4_4_1.jpg | |Main_Picture=SolarOSE_G4_4_1.jpg | ||
}} | }} | ||
− | {{ | + | {{Introduction|}} |
{{Separator}} | {{Separator}} | ||
− | {{ | + | {{Materials |
|Step_Picture_01=No-image-yet.jpg | |Step_Picture_01=No-image-yet.jpg | ||
|Step_Picture_02=No-image-yet.jpg | |Step_Picture_02=No-image-yet.jpg | ||
Ligne 24 : | Ligne 24 : | ||
}} | }} | ||
{{Separator}} | {{Separator}} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=<translate>Main beam</translate> | |Step_Title=<translate>Main beam</translate> | ||
|Step_Content=<translate>Cut the 30x30x2300 mm square tube. | |Step_Content=<translate>Cut the 30x30x2300 mm square tube. | ||
Ligne 35 : | Ligne 35 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=<translate>Lateral 'L' profiles</translate> | |Step_Title=<translate>Lateral 'L' profiles</translate> | ||
|Step_Content=<translate>Cut two L profiles 30x60 mm, thick of 3 mm and long of 2100 mm. | |Step_Content=<translate>Cut two L profiles 30x60 mm, thick of 3 mm and long of 2100 mm. | ||
Ligne 51 : | Ligne 51 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=<translate>Junction of the main beam and the lateral L profiles</translate> | |Step_Title=<translate>Junction of the main beam and the lateral L profiles</translate> | ||
|Step_Content=<translate>Cut, drill, weld according to the 3D model.</translate> | |Step_Content=<translate>Cut, drill, weld according to the 3D model.</translate> | ||
Ligne 61 : | Ligne 61 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=<translate>Hanger</translate> | |Step_Title=<translate>Hanger</translate> | ||
|Step_Content=<translate>Print the 10 hangers at the cutting laser. The material used is a wood board (for example laminated structural wood) with a thickness of 10 mm. | |Step_Content=<translate>Print the 10 hangers at the cutting laser. The material used is a wood board (for example laminated structural wood) with a thickness of 10 mm. | ||
Ligne 75 : | Ligne 75 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Notes|}} |
Auteur OSE France | Dernière modification 9/12/2019 par Clementflipo
SolarOSE_G4_4_1.jpg en none Creation 0
Cut the 30x30x2300 mm square tube. Drill the fixation holes of the tepee. Drill and tap at 5 mm diameter the fixation holes of the junction.
Cut two L profiles 30x60 mm, thick of 3 mm and long of 2100 mm.
Drill and tap the fixation holes of the exterior cover, screw with a diameter 4 mm.
Drill the fixation holes at the junction, as depicted in the 3D model. Improvement: drill 2 holes on the side and none on the bottom of the L.
Weld a flat at each edge of the L (for the fixation on the “tepee”…).
Cut, drill, weld according to the 3D model.
Print the 10 hangers at the cutting laser. The material used is a wood board (for example laminated structural wood) with a thickness of 10 mm.
Cut shapes of 2 hangers (with a cutting laser or manually), without emptying them. They are needed for the secondary reflector in order to close the receiver on its edges.
Link to the file for printing!
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #