Line 150: | Line 150: | ||
#Stand one leg unit upward, so you can see down the 1200mm section. Slide 4 T-nuts total (2 in each rail) up to the corner joint. (image 2) | #Stand one leg unit upward, so you can see down the 1200mm section. Slide 4 T-nuts total (2 in each rail) up to the corner joint. (image 2) | ||
− | #<u>SPECIAL STEP:</u> on the 1200mm beam, opposite side from where the side plate was installed - Slide 2 nuts into each of the rails. These will be used in a future step. Repeat on the other 1200mm beam. | + | #<u>SPECIAL STEP:</u> on the 1200mm beam, opposite side from where the side plate was installed - Slide 2 nuts into each of the rails. These will be used in a future step. Repeat on the other 1200mm beam. |
#Attach the side plate (image 3) using 4 M8x16 Bolts with 4 washers. | #Attach the side plate (image 3) using 4 M8x16 Bolts with 4 washers. | ||
##NOTE: the 45° side should face the "bottom" of the eventual table. | ##NOTE: the 45° side should face the "bottom" of the eventual table. | ||
Line 156: | Line 156: | ||
##NOTE: ensure that each corner plate '''mirrors''' each other across the 1200mm beam axis. They should be facing the same direction and away from the side plate from the previous step. | ##NOTE: ensure that each corner plate '''mirrors''' each other across the 1200mm beam axis. They should be facing the same direction and away from the side plate from the previous step. | ||
#Slide 8 total T-nuts into a 520mm beam. They should be split in half, 4 at one end, and 4 at the other. (Image 4) | #Slide 8 total T-nuts into a 520mm beam. They should be split in half, 4 at one end, and 4 at the other. (Image 4) | ||
+ | #<u>SPECIAL STEP:</u> On only ONE of the 520mm beams, add 4 T-nuts, 2 in each rail on the opposite side that you used for Step 5. | ||
#Combine the two "'''staple'''" sections by adding the 520mm beam (pre-loaded with T-nuts) using the same M8x16mm, washer combination as before. (image 5) | #Combine the two "'''staple'''" sections by adding the 520mm beam (pre-loaded with T-nuts) using the same M8x16mm, washer combination as before. (image 5) | ||
#Repeat on the other side. (image 6) | #Repeat on the other side. (image 6) | ||
Line 165: | Line 166: | ||
|Step_Picture_02=PP_Shredder_Pro_1PXL_20210913_184439835.MP.jpg | |Step_Picture_02=PP_Shredder_Pro_1PXL_20210913_184439835.MP.jpg | ||
|Step_Picture_03=PP_Shredder_Pro_1PXL_20210913_184424674.MP.jpg | |Step_Picture_03=PP_Shredder_Pro_1PXL_20210913_184424674.MP.jpg | ||
+ | |Step_Picture_03_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":800,"height":450,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.75,"scaleY":0.75,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://wikifab.org/images/thumb/e/e0/PP_Shredder_Pro_1PXL_20210913_184424674.MP.jpg/800px-PP_Shredder_Pro_1PXL_20210913_184424674.MP.jpg","filters":[]},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":174.95,"top":49.02,"width":65.6,"height":48.82,"fill":"#000000","stroke":"#000000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.24,"scaleY":1.24,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Special Step","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":375.67,"top":89.82,"width":262.38,"height":48.82,"fill":"#000000","stroke":"#000000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.05,"scaleY":1.05,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"add 2 nuts on opposite side\nto each rail","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"wfline","version":"2.4.6","originX":"center","originY":"center","left":529,"top":110,"width":54,"height":58,"fill":"rgba(255,0,0,0)","stroke":"#000000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-27,"x2":27,"y1":-29,"y2":29},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":502,"top":81,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":556,"top":139,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":537,"top":152.5,"width":40,"height":29,"fill":"rgba(255,0,0,0)","stroke":"#000000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":20,"x2":-20,"y1":-14.5,"y2":14.5,"x2a":0.8879494395752019,"y2a":9.23753211793648,"x2b":-8.503531703799695,"y2b":-3.7162349763737215},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":557,"top":138,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":517,"top":167,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":534,"top":190.5,"width":40,"height":29,"fill":"rgba(255,0,0,0)","stroke":"#000000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":20,"x2":-20,"y1":-14.5,"y2":14.5,"x2a":0.8879494395752019,"y2a":9.23753211793648,"x2b":-8.503531703799695,"y2b":-3.7162349763737215},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":554,"top":176,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":514,"top":205,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586}],"height":338,"width":600} | ||
|Step_Picture_04=PP_Shredder_Pro_PXL_20210913_190202336.MP.jpg | |Step_Picture_04=PP_Shredder_Pro_PXL_20210913_190202336.MP.jpg | ||
|Step_Picture_05=PP_Shredder_Pro_PXL_20210913_190407012.MP.jpg | |Step_Picture_05=PP_Shredder_Pro_PXL_20210913_190407012.MP.jpg | ||
Line 184: | Line 186: | ||
16x M8x20mm Bolts | 16x M8x20mm Bolts | ||
− | |||
− | #</translate> | + | |
+ | <nowiki>*</nowiki><u>A quick note about bracket orientation</u>. In image 2 you will see that the brackets are not the same on both sides. Here we have flipped one, so you can see the difference. One of the holes sits atop a raised lip, while the other is flush. The raised lip hole is ''closer'' to the brackets outside edge. The flush hole is ''farther'' from the outside edge. This matters for order of operations. When installing, you must install in the flush hole '''first''', and the hole with the raised lip '''second.''' If you do it in reverse the bolt will block access to the other hole. :) | ||
+ | |||
+ | ==== Steps ==== | ||
+ | |||
+ | # Slide 4 nuts into the 520mm beam (2 in each rail). | ||
+ | # Attach the 4 brackets loosely using M8x20mm bolts and washers. (image 3) | ||
+ | ## Note the orientation of the holes. All 4 bolts should go in flush holes, not raised lip holes. (figure 4) | ||
+ | # With the table flipped on its end, position the 520mm beam in place, and slide 2 T-nuts in the rails to meet the brackets. Secure with same bolt washer combo. | ||
+ | # Repeat this process on the other side of the 520mm beam. | ||
+ | # Repeat steps 1-4 on the opposite side.</translate> | ||
|Step_Picture_00=PP_Shredder_Pro_PXL_20210913_191021332.MP.jpg | |Step_Picture_00=PP_Shredder_Pro_PXL_20210913_191021332.MP.jpg | ||
|Step_Picture_01=PP_Shredder_Pro_PXL_20211012_220820636.jpg | |Step_Picture_01=PP_Shredder_Pro_PXL_20211012_220820636.jpg | ||
− | |Step_Picture_02= | + | |Step_Picture_02=PP_Shredder_Pro_PXL_20210913_191436622.MP.jpg |
− | |Step_Picture_03= | + | |Step_Picture_03=PP_Shredder_Pro_PXL_20210913_191820142.MP.jpg |
|Step_Picture_04=PP_Shredder_Pro_PXL_20210913_192421299.MP.jpg | |Step_Picture_04=PP_Shredder_Pro_PXL_20210913_192421299.MP.jpg | ||
|Step_Picture_05=PP_Shredder_Pro_PXL_20210913_192452373.MP.jpg | |Step_Picture_05=PP_Shredder_Pro_PXL_20210913_192452373.MP.jpg |
Author PPatASU | Last edit 29/11/2021 by PPatASU
No image yet
preciousplastic, recycling, Open Source, plastic, shredder
Hammer
(punch) for knocking out leftover metal slugs
Files
Mallet
Socket wrench( 2x)
Tape measure
Screwdriver (directing the slide nuts)
Marker
Parts Needed:
Aluminum Extrusion
Profile | Length (mm) | Quantity |
---|---|---|
8080 | 520 | 4 |
8080 | 600 | 4 |
8080 | 1200 | 2 |
4080 | 520 | 1 |
4080 | 455 | 1 |
Corner Plates | 4 |
Rectangular Plates | 4 |
Brackets | 32 |
M8 x 20 Bolts | 72 |
M8 x 16 Bolts | 77 |
Slot Nuts | 149 |
Washers | 149 |
Notse to tyler:
only 24 brackets in use?
64 M8x16
48 M8X20
112 washers and nuts
XX Socket Wrench
Screwdriver
4x 8080*600mm
2x 8080*1200mm
4x Side Plates
32x T nuts
32x Washers
32x M8x16mm Bolts
You now have a staple shape. Repeat.
XX Socket Wrench
Screwdriver
2x 8080*520mm
4x Corner Plates
40x T nuts
32x Washers
32x M8x16mm Bolts
You should now have a very solid table base!
XX Socket Wrench
Screwdriver
2x 8080*520mm
8x Brackets
16x T nuts
16x Washers
16x M8x20mm Bolts
*A quick note about bracket orientation. In image 2 you will see that the brackets are not the same on both sides. Here we have flipped one, so you can see the difference. One of the holes sits atop a raised lip, while the other is flush. The raised lip hole is closer to the brackets outside edge. The flush hole is farther from the outside edge. This matters for order of operations. When installing, you must install in the flush hole first, and the hole with the raised lip second. If you do it in reverse the bolt will block access to the other hole. :)
en none 0 Draft
You entered an invalid page name, with one or many of the following characters :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #