Line 150: | Line 150: | ||
#Stand one leg unit upward, so you can see down the 1200mm section. Slide 4 T-nuts total (2 in each rail) up to the corner joint. (image 2) | #Stand one leg unit upward, so you can see down the 1200mm section. Slide 4 T-nuts total (2 in each rail) up to the corner joint. (image 2) | ||
#Attach the side plate (image 3) using 4 M8x16 Bolts with 4 washers. | #Attach the side plate (image 3) using 4 M8x16 Bolts with 4 washers. | ||
− | ##NOTE: the 45° side should face the "bottom" of the eventual table. | + | ##NOTE: the 45° side should face the "bottom" of the eventual table. |
#Repeat on the remaining three 600mm legs. | #Repeat on the remaining three 600mm legs. | ||
− | ##NOTE: ensure that each corner | + | ##NOTE: ensure that each corner plate '''mirrors''' each other across the 1200mm beam axis. They should be facing the same direction and away from the side plate from the previous step. |
#Slide 8 total T-nuts into a 520mm beam. They should be split in half, 4 at one end, and 4 at the other. (Image 4) | #Slide 8 total T-nuts into a 520mm beam. They should be split in half, 4 at one end, and 4 at the other. (Image 4) | ||
#Combine the two "'''staple'''" sections by adding the 520mm beam (pre-loaded with T-nuts) using the same M8x16mm, washer combination as before. (image 5) | #Combine the two "'''staple'''" sections by adding the 520mm beam (pre-loaded with T-nuts) using the same M8x16mm, washer combination as before. (image 5) | ||
Line 161: | Line 161: | ||
|Step_Picture_01=PP_Shredder_Pro_1PXL_20210913_184210669.MP.jpg | |Step_Picture_01=PP_Shredder_Pro_1PXL_20210913_184210669.MP.jpg | ||
|Step_Picture_02=PP_Shredder_Pro_1PXL_20210913_184439835.MP.jpg | |Step_Picture_02=PP_Shredder_Pro_1PXL_20210913_184439835.MP.jpg | ||
− | |Step_Picture_03= | + | |Step_Picture_03=PP_Shredder_Pro_1PXL_20210913_184424674.MP.jpg |
|Step_Picture_04=PP_Shredder_Pro_PXL_20210913_190202336.MP.jpg | |Step_Picture_04=PP_Shredder_Pro_PXL_20210913_190202336.MP.jpg | ||
|Step_Picture_05=PP_Shredder_Pro_PXL_20210913_190407012.MP.jpg | |Step_Picture_05=PP_Shredder_Pro_PXL_20210913_190407012.MP.jpg |
Author PPatASU | Last edit 29/11/2021 by PPatASU
No image yet
preciousplastic, recycling, Open Source, plastic, shredder
Hammer
(punch) for knocking out leftover metal slugs
Files
Mallet
Socket wrench( 2x)
Tape measure
Screwdriver (directing the slide nuts)
Marker
Parts Needed:
Aluminum Extrusion
Profile | Length (mm) | Quantity |
---|---|---|
8080 | 520 | 4 |
8080 | 600 | 4 |
8080 | 1200 | 2 |
4080 | 520 | 1 |
4080 | 455 | 1 |
Corner Plates | 4 |
Rectangular Plates | 4 |
Brackets | 32 |
M8 x 20 Bolts | 72 |
M8 x 16 Bolts | 77 |
Slot Nuts | 149 |
Washers | 149 |
Notse to tyler:
only 24 brackets in use?
64 M8x16
48 M8X20
112 washers and nuts
XX Socket Wrench
Screwdriver
4x 8080*600mm
2x 8080*1200mm
4x Side Plates
32x T nuts
32x Washers
32x M8x16mm Bolts
XX Socket Wrench
Screwdriver
2x 8080*520mm
4x Corner Plates
32x T nuts
32x Washers
32x M8x16mm Bolts
You should now have a very solid table base!
en none 0 Draft
You entered an invalid page name, with one or many of the following characters :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #