Line 87: | Line 87: | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title=<translate>Leg Linear | + | |Step_Title=<translate>Leg Linear Rail Prep</translate> |
− | |Step_Content=<translate>==== Tools ==== | + | |Step_Content=<translate>====Tools==== |
(welder?) | (welder?) | ||
Line 99: | Line 99: | ||
1/4-20 Tap | 1/4-20 Tap | ||
− | ==== Parts ==== | + | ====Parts==== |
4x Linear rail plates (w/ 90degree stopper plate) | 4x Linear rail plates (w/ 90degree stopper plate) | ||
Line 107: | Line 107: | ||
<br /> | <br /> | ||
− | ==== Steps ==== | + | ====Steps==== |
− | # (if not already done) weld the small stopper plate to the end of the long linear rail leg plate. Be sure you have two mirrored sets and not four identical pieces. (see image 5) | + | #(if not already done) weld the small stopper plate to the end of the long linear rail leg plate. Be sure you have two mirrored sets and not four identical pieces. (see image 5) |
− | # Grind down the welds (or avoid welding where the linear slide will attach.) This is a very snug fit and you may have to make some room for proper alignment | + | #Grind down the welds (or avoid welding where the linear slide will attach.) This is a very snug fit and you may have to make some room for proper alignment |
− | ## You can also drill out the slide rail mounting holes (aluminum) to give yourself a little more room for a proper fit. | + | ##You can also drill out the slide rail mounting holes (aluminum) to give yourself a little more room for a proper fit. |
− | # Image 4 shows the holes not in perfect alignment, so you may have to grind the linear rail bar down until the wholes are perfectly aligned. | + | #Image 4 shows the holes not in perfect alignment, so you may have to grind the linear rail bar down until the wholes are perfectly aligned. |
− | # Tap all 8 small holes to 1/4"-20 | + | #Tap all 8 small holes to 1/4"-20 |
− | # Align and install the linear rail to the plate. (repeat for all 4 plates)</translate> | + | #Align and install the linear rail to the plate. Add the bearing carriages. (repeat for all 4 plates)</translate> |
|Step_Picture_00=PP_Sheetpress_PXL_20220114_184026556.jpg | |Step_Picture_00=PP_Sheetpress_PXL_20220114_184026556.jpg | ||
|Step_Picture_01=PP_Sheetpress_PXL_20220114_182900141.jpg | |Step_Picture_01=PP_Sheetpress_PXL_20220114_182900141.jpg | ||
Line 122: | Line 122: | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title=<translate></translate> | + | |Step_Title=<translate>Leg linear Rail install</translate> |
− | |Step_Content=<translate>==== Tools ==== | + | |Step_Content=<translate>====Tools==== |
+ | 1/2" socket | ||
− | ==== Parts ==== | + | ====Parts==== |
16x m8x20 bolts | 16x m8x20 bolts | ||
− | + | 16x m8 washers | |
+ | |||
+ | 16x m8 t-nuts | ||
+ | |||
+ | 4x 8080 extrusion | ||
+ | |||
+ | ====Steps==== | ||
+ | |||
+ | # Slide 4 t nuts into the 8080 extrusion rail. | ||
+ | # Position one linear slide just next to the rail so you can align the t-nuts to the holes as this will again be a "blind" install. | ||
+ | # Attach the linear slide so it is flush with the end of the extrusion. | ||
+ | # repeat for all 4 rails so you have 2 mirrored pairs. | ||
− | |||
<br /></translate> | <br /></translate> | ||
+ | |Step_Picture_00=PP_Sheetpress_PXL_20220114_190517138.jpg | ||
+ | |Step_Picture_01=PP_Sheetpress_PXL_20220114_190641454.jpg | ||
+ | |Step_Picture_02=PP_Sheetpress_PXL_20220114_192000012.jpg | ||
}} | }} | ||
{{Notes | {{Notes |
Author PPatASU | Last edit 2/03/2022 by PPatASU
No image yet
Recycle, Plastic, sheet, sheetpress, preciousplastic Creation
*The following 2 steps will be used to make 2 identical plate assemblies. The parts listed are for 1 assembly (so double everything if you're making two plates at a time)
1/4"-20 tap + tap handle
countersink (or anything over 1/4" bit) for hole cleanup
1/2" Socket
1 meter aluminum sheet
2x 1000mm 4080 extrusion
4x 920mm 4080 extrusion
4x 286mm 4080 extrusion
2x266mm 4080 extrusion
156 T-nuts (16*9) + 12)
156 M8x16mm Bolts
156 M8 washers
Attaching the exterior beams to the plate
same as above
36 corner brackets
(welder?)
Drill press
Grinder
Vice
1/4-20 Tap
4x Linear rail plates (w/ 90degree stopper plate)
4x Linear rail posts
16x 1/4"-20 x 3/8" bolts
1/2" socket
16x m8x20 bolts
16x m8 washers
16x m8 t-nuts
4x 8080 extrusion
en none 0 Draft
You entered an invalid page name, with one or many of the following characters :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #