Difference between revisions of "Biped dancing robot"

(convert properties for internationnalized Wikifab)
(Cette version a été marquée pour être traduite)
Line 5: Line 5:
 
|Type=Creation
 
|Type=Creation
 
|Area=Robotics, Electronics, Play & Outside
 
|Area=Robotics, Electronics, Play & Outside
|Description=<translate>Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard Arduino UNO board with easier connections and supports.</translate>
+
|Description=<translate><!--T:1--> Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard Arduino UNO board with easier connections and supports.</translate>
 
|Difficulty=Medium
 
|Difficulty=Medium
 
|Cost=45
 
|Cost=45
Line 15: Line 15:
 
}}
 
}}
 
{{ {{tntn|Introduction}}
 
{{ {{tntn|Introduction}}
|Introduction=<translate>Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard arduino UNO board. original project Zowi https://github.com/bqlabs/zowi</translate>
+
|Introduction=<translate><!--T:2--> Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard arduino UNO board. original project Zowi https://github.com/bqlabs/zowi</translate>
 
}}
 
}}
 
{{ {{tntn|Materials}}
 
{{ {{tntn|Materials}}
|Material=<translate>Arduino UNO
+
|Material=<translate><!--T:3-->
 +
Arduino UNO
 
Nano breadboard or
 
Nano breadboard or
 
Buzzer
 
Buzzer
Line 43: Line 44:
 
{{Separator}}
 
{{Separator}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>3D print parts</translate>
+
|Step_Title=<translate><!--T:4--> 3D print parts</translate>
|Step_Content=<translate>3D .stl files here: http://www.thingiverse.com/thing:1378605
+
|Step_Content=<translate><!--T:5-->
 +
3D .stl files here: http://www.thingiverse.com/thing:1378605
 
Find a way to 3d print the parts, they are designed for no supports so is very easy to print with 20%  infill and 0.2mm resolution.</translate>
 
Find a way to 3d print the parts, they are designed for no supports so is very easy to print with 20%  infill and 0.2mm resolution.</translate>
 
|Step_Picture_00=3dprinter.JPG
 
|Step_Picture_00=3dprinter.JPG
Line 54: Line 56:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Pre assemble</translate>
+
|Step_Title=<translate><!--T:6--> Pre assemble</translate>
|Step_Content=<translate>There is many was to build Tito, but one recommendation is before the connect the servos is to assemble the servo disk pieces to the legs, then put the servos in the body and the feet..</translate>
+
|Step_Content=<translate><!--T:7--> There is many was to build Tito, but one recommendation is before the connect the servos is to assemble the servo disk pieces to the legs, then put the servos in the body and the feet..</translate>
 
|Step_Picture_00=Tito (3).jpg
 
|Step_Picture_00=Tito (3).jpg
 
|Step_Picture_01=Tito parts.jpg
 
|Step_Picture_01=Tito parts.jpg
Line 64: Line 66:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>The Schematic</translate>
+
|Step_Title=<translate><!--T:8--> The Schematic</translate>
|Step_Content=<translate>Follow the picture for the connections.
+
|Step_Content=<translate><!--T:9-->
 +
Follow the picture for the connections.
 
HC-SR04 Ultrasound sensor (not connected in the schematic; trig for pin 8 and echo for pin 9).
 
HC-SR04 Ultrasound sensor (not connected in the schematic; trig for pin 8 and echo for pin 9).
 
During the making process you may need to disconnect and connect constantly so just keep this schematic present for further fixes.</translate>
 
During the making process you may need to disconnect and connect constantly so just keep this schematic present for further fixes.</translate>
Line 76: Line 79:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Test the position of the servos</translate>
+
|Step_Title=<translate><!--T:10--> Test the position of the servos</translate>
|Step_Content=<translate>In the picture the cables are disconnected but the idea here is to upload a code to the Arduino board (https://github.com/agomezgar/tutoriales/tree/master/tutorialZowi3/prepararServosparaMontaje) that will put the all servos in 90 degrees and then fix the right angle for the crank discs in the body and the feet. Tito should be in a neutral position like the photo. then you can fix all the servos with the screw axis.</translate>
+
|Step_Content=<translate><!--T:11--> In the picture the cables are disconnected but the idea here is to upload a code to the Arduino board (https://github.com/agomezgar/tutoriales/tree/master/tutorialZowi3/prepararServosparaMontaje) that will put the all servos in 90 degrees and then fix the right angle for the crank discs in the body and the feet. Tito should be in a neutral position like the photo. then you can fix all the servos with the screw axis.</translate>
 
|Step_Picture_00=Tito align.jpg
 
|Step_Picture_00=Tito align.jpg
 
|Step_Picture_01=No-image-yet.jpg
 
|Step_Picture_01=No-image-yet.jpg
Line 86: Line 89:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Assemble Arduino board</translate>
+
|Step_Title=<translate><!--T:12--> Assemble Arduino board</translate>
|Step_Content=<translate>This design make it easy to fix any Arduino Uno compatible board (in my case a DFRduino UNO) in the head part, you can use up to 4 screws.</translate>
+
|Step_Content=<translate><!--T:13--> This design make it easy to fix any Arduino Uno compatible board (in my case a DFRduino UNO) in the head part, you can use up to 4 screws.</translate>
 
|Step_Picture_00=Tito (30).JPG
 
|Step_Picture_00=Tito (30).JPG
 
|Step_Picture_01=No-image-yet.jpg
 
|Step_Picture_01=No-image-yet.jpg
Line 96: Line 99:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Final assembly</translate>
+
|Step_Title=<translate><!--T:14--> Final assembly</translate>
|Step_Content=<translate>If all connections are secured you can close the head part and fix it to the body using the lateral screws.</translate>
+
|Step_Content=<translate><!--T:15--> If all connections are secured you can close the head part and fix it to the body using the lateral screws.</translate>
 
|Step_Picture_00=Tito (15).jpg
 
|Step_Picture_00=Tito (15).jpg
 
|Step_Picture_01=No-image-yet.jpg
 
|Step_Picture_01=No-image-yet.jpg
Line 106: Line 109:
 
}}
 
}}
 
{{ {{tntn|Tuto Step}}
 
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Programming</translate>
+
|Step_Title=<translate><!--T:16--> Programming</translate>
|Step_Content=<translate>All libraries and Arduino source code are in this Github repository: https://github.com/bqlabs/zowi
+
|Step_Content=<translate><!--T:17-->
 +
All libraries and Arduino source code are in this Github repository: https://github.com/bqlabs/zowi
 
Just connect your USB cable to Arduino and upload the codes
 
Just connect your USB cable to Arduino and upload the codes
 
There are many programmed movements for the robot like walk different directions, raise, tilt and dance.</translate>
 
There are many programmed movements for the robot like walk different directions, raise, tilt and dance.</translate>
Line 118: Line 122:
 
}}
 
}}
 
{{ {{tntn|Notes}}
 
{{ {{tntn|Notes}}
|Notes=<translate>3D print files: http://www.thingiverse.com/thing:137860
+
|Notes=<translate><!--T:18-->
 +
3D print files: http://www.thingiverse.com/thing:137860
 
Code: https://github.com/bqlabs/zowi
 
Code: https://github.com/bqlabs/zowi
 
}}
 
}}

Revision as of 12:23, 11 August 2017

Author avatarCamilo Parra Palacio | Last edit 9/12/2019 by Clementflipo

Tito (11).jpg
Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard Arduino UNO board with easier connections and supports.
Difficulty
Medium
Duration
10 hour(s)
Categories
Robotics, Electronics, ⧼wf-propertyvalue-area-Play & Outside⧽
Cost
45 USD ($)
Other languages:
English

Introduction

Tito is a Biped dancing DIY robot, derivative from Zowi and Bob, basically has been adapted to an standard arduino UNO board. original project Zowi https://github.com/bqlabs/zowi

Materials

Arduino UNO Nano breadboard or Buzzer Futaba servo S3003 x4 HC-SR04 Ultrasound sensor Powerbank (optional) Nut M3 x20 Screw M3 x20 3d print Head 3d print Base 3d print Leg x2 3d print Foot R 3d print Foot L

Tools

3d printer, allen key and screwdriver

Step 1 - 3D print parts

3D .stl files here: http://www.thingiverse.com/thing:1378605 Find a way to 3d print the parts, they are designed for no supports so is very easy to print with 20% infill and 0.2mm resolution.

Step 2 - Pre assemble

There is many was to build Tito, but one recommendation is before the connect the servos is to assemble the servo disk pieces to the legs, then put the servos in the body and the feet..

Step 3 - The Schematic

Follow the picture for the connections. HC-SR04 Ultrasound sensor (not connected in the schematic; trig for pin 8 and echo for pin 9). During the making process you may need to disconnect and connect constantly so just keep this schematic present for further fixes.

Step 4 - Test the position of the servos

In the picture the cables are disconnected but the idea here is to upload a code to the Arduino board (https://github.com/agomezgar/tutoriales/tree/master/tutorialZowi3/prepararServosparaMontaje) that will put the all servos in 90 degrees and then fix the right angle for the crank discs in the body and the feet. Tito should be in a neutral position like the photo. then you can fix all the servos with the screw axis.

Step 5 - Assemble Arduino board

This design make it easy to fix any Arduino Uno compatible board (in my case a DFRduino UNO) in the head part, you can use up to 4 screws.

Step 6 - Final assembly

If all connections are secured you can close the head part and fix it to the body using the lateral screws.

Step 7 - Programming

All libraries and Arduino source code are in this Github repository: https://github.com/bqlabs/zowi Just connect your USB cable to Arduino and upload the codes There are many programmed movements for the robot like walk different directions, raise, tilt and dance.

Notes and references

3D print files: http://www.thingiverse.com/thing:137860 Code: https://github.com/bqlabs/zowi

Comments

Yes