Hub type = SPLIT hub with feather keyway and thread for setscrews ROTEXROTEX®ROTEX ®ROTEXROTEX ROTEX® Flexible jaw couplings Properties of standard spiders For continuously updated data please Technical description. General Description ROTEX ®GS – couplings are designed to transmit torque between drive and driven components with zero-backlash via For continuously updated data please refer to our online catalogue at Components For legend of pictogram please refer to flapper on the cover ROTEX® A-H Flexible jaw couplings Drop-out center design coupling Type A-H CAUTION: With maximum bore the feather keyways are offset to each other by approx°! permissible circumferential speed for double-cardanic ROTEX® DKM and ZS-DKM-SH coupling ism/s, with higher speeds please consult with KTR blind assembly. The couplings are certified and confirmed according to EC standard/9/EC (ATEX) as units of category 2G/2D and thus suitable for the use in hazardous areas of zone 1, 2,and Please read through our information included in the respective Type Examination ROTEX®-SPLIT hub material sizesand= sintered steel; hub material sizesto= EN-GJL. It is convincing even with critical applica-tions by its backlash-free power ROTEX® GS is a three-part, axial plug-in coupling backlash-free under prestress. ROTEX® GS is apart, axial plug-in coupling backlash-free under pre-stress. It is convincing even with critical applications by its backlash-free power transmission, its Curved Jaw (Rotex) CouplingsEvery effort has been taken to ensure that the data listed in this catalogue is correct. for hub type ROTEX® couplings are suitable for power transmission in drives in hazardous areas. As defined by the spider, ROTEX ®GS couplings are suitable for moderate temperature ranges. D max. TableFinish bores Size Unbo-red Finish bore in mm D min. ROTEX®-SPLIT hub material sizesand= sintered steel; hub material sizesto= EN-GJL. = rated torque of the coupling T KN xFor coupling selection see catalogue drive technology ROTEX® GS 2) When using the spiderShD, we recommend to use hubs made of steel. Material spacer Al-H. Hub type = SPLIT hub with feather keyway and thread for setscrews. Together these features reduce the maintenance required during the life-cycle of the coupling. Finer Power Transmissions P/L will not accept liability 1) Maximum torque of the coupling T Kmax. The max.
Hub type = SPLIT hub with feather keyway and thread for setscrews ROTEXROTEX®ROTEX ®ROTEXROTEX ROTEX® Flexible jaw couplings Properties of standard spiders For continuously updated data please Technical description. General Description ROTEX ®GS – couplings are designed to transmit torque between drive and driven components with zero-backlash via For continuously updated data please refer to our online catalogue at Components For legend of pictogram please refer to flapper on the cover ROTEX® A-H Flexible jaw couplings Drop-out center design coupling Type A-H CAUTION: With maximum bore the feather keyways are offset to each other by approx°! permissible circumferential speed for double-cardanic ROTEX® DKM and ZS-DKM-SH coupling ism/s, with higher speeds please consult with KTR blind assembly. The couplings are certified and confirmed according to EC standard/9/EC (ATEX) as units of category 2G/2D and thus suitable for the use in hazardous areas of zone 1, 2,and Please read through our information included in the respective Type Examination ROTEX®-SPLIT hub material sizesand= sintered steel; hub material sizesto= EN-GJL. It is convincing even with critical applica-tions by its backlash-free power ROTEX® GS is a three-part, axial plug-in coupling backlash-free under prestress. ROTEX® GS is apart, axial plug-in coupling backlash-free under pre-stress. It is convincing even with critical applications by its backlash-free power transmission, its Curved Jaw (Rotex) CouplingsEvery effort has been taken to ensure that the data listed in this catalogue is correct. for hub type ROTEX® couplings are suitable for power transmission in drives in hazardous areas. As defined by the spider, ROTEX ®GS couplings are suitable for moderate temperature ranges. D max. TableFinish bores Size Unbo-red Finish bore in mm D min. ROTEX®-SPLIT hub material sizesand= sintered steel; hub material sizesto= EN-GJL. = rated torque of the coupling T KN xFor coupling selection see catalogue drive technology ROTEX® GS 2) When using the spiderShD, we recommend to use hubs made of steel. Material spacer Al-H. Hub type = SPLIT hub with feather keyway and thread for setscrews. Together these features reduce the maintenance required during the life-cycle of the coupling. Finer Power Transmissions P/L will not accept liability 1) Maximum torque of the coupling T Kmax. The max.
Français
English
Deutsch
Español
Italiano
Português