(Mise à jour pour être en accord avec la nouvelle version de la source de la page) |
(update property name) |
||
Ligne 1 : | Ligne 1 : | ||
− | {{ | + | {{Tuto Details |
|Main_Picture=ZipStich Chair Final.png | |Main_Picture=ZipStich Chair Final.png | ||
|Licences=Attribution (CC BY) | |Licences=Attribution (CC BY) | ||
Ligne 15 : | Ligne 15 : | ||
|IsTranslation=1 | |IsTranslation=1 | ||
}} | }} | ||
− | {{ | + | {{Introduction |
|Introduction=Chairs are generally more difficult to make than benches or stools, but here's one that can be made by stitching (or what we're calling 'stiching') plywood pieces with zip ties. | |Introduction=Chairs are generally more difficult to make than benches or stools, but here's one that can be made by stitching (or what we're calling 'stiching') plywood pieces with zip ties. | ||
I was able to make 2 chairs out of a single 4’ by 8’ sheet of plywood. The chairs I built with ¼" thick plywood are strong, but over time the holes could wear through, so I'd recommend using ½" thick plywood. Feel free to do some experimenting with the design of the chair and share your results. | I was able to make 2 chairs out of a single 4’ by 8’ sheet of plywood. The chairs I built with ¼" thick plywood are strong, but over time the holes could wear through, so I'd recommend using ½" thick plywood. Feel free to do some experimenting with the design of the chair and share your results. | ||
}} | }} | ||
− | {{ | + | {{TutoVideo |
|TutoVideoService=youtube | |TutoVideoService=youtube | ||
|TutoVideoURL=https://www.youtube.com/watch?v=2jLEsCf6iR0 | |TutoVideoURL=https://www.youtube.com/watch?v=2jLEsCf6iR0 | ||
}} | }} | ||
− | {{ | + | {{Materials |
|Step_Picture_00=Hmm ep21 zipstichchair supplies.jpg | |Step_Picture_00=Hmm ep21 zipstichchair supplies.jpg | ||
|Step_Picture_01=No-image-yet.jpg | |Step_Picture_01=No-image-yet.jpg | ||
Ligne 40 : | Ligne 40 : | ||
* Long Nose Pliers | * Long Nose Pliers | ||
}} | }} | ||
− | {{ | + | {{Separator}} |
− | {{ | + | {{Tuto Step |
|Step_Title=Measure and mark the plywood strips | |Step_Title=Measure and mark the plywood strips | ||
|Step_Content=Measure and mark the plywood with a pencil. | |Step_Content=Measure and mark the plywood with a pencil. | ||
Ligne 51 : | Ligne 51 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Cut the pieces | |Step_Title=Cut the pieces | ||
|Step_Content=I used my Circular Saw with a plywood blade to make the cuts. The laser guide makes it really easy to follow the lines. If you don’t have a laser then clamp a guide to the plywood. | |Step_Content=I used my Circular Saw with a plywood blade to make the cuts. The laser guide makes it really easy to follow the lines. If you don’t have a laser then clamp a guide to the plywood. | ||
Ligne 61 : | Ligne 61 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Sand the edges | |Step_Title=Sand the edges | ||
|Step_Content=Smooth the edges with 120-220 grit sandpaper. | |Step_Content=Smooth the edges with 120-220 grit sandpaper. | ||
Ligne 71 : | Ligne 71 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Mark the holes | |Step_Title=Mark the holes | ||
|Step_Content=I measured a line 1/2” from the edges and marked an X every 1" inch down the line to indicate drill marks. | |Step_Content=I measured a line 1/2” from the edges and marked an X every 1" inch down the line to indicate drill marks. | ||
Ligne 81 : | Ligne 81 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Drill the holes | |Step_Title=Drill the holes | ||
|Step_Content=I clamped 2 to 3 boards together to drill the holes on multiple pieces at the same time. | |Step_Content=I clamped 2 to 3 boards together to drill the holes on multiple pieces at the same time. | ||
Ligne 91 : | Ligne 91 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Loosely stitch the boards together | |Step_Title=Loosely stitch the boards together | ||
|Step_Content=I zipped a series of loops into the drilled holes in the first piece. Then I strung zip ties through the holes in the second piece and the zip tie loops in the first piece. This creates a zip tie to zip tie connection/link. Keep the links loose for now. | |Step_Content=I zipped a series of loops into the drilled holes in the first piece. Then I strung zip ties through the holes in the second piece and the zip tie loops in the first piece. This creates a zip tie to zip tie connection/link. Keep the links loose for now. | ||
Ligne 101 : | Ligne 101 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Shape and tighten | |Step_Title=Shape and tighten | ||
|Step_Content=Shaping and tightening the zip ties is an incremental process that requires a bit of patience. The good news is that you can always cut and redo zip ties if you make a mistake. Use long nose pliers to tighten the ties and diagonal pliers to cut the long ends. | |Step_Content=Shaping and tightening the zip ties is an incremental process that requires a bit of patience. The good news is that you can always cut and redo zip ties if you make a mistake. Use long nose pliers to tighten the ties and diagonal pliers to cut the long ends. | ||
Ligne 111 : | Ligne 111 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Add supports (Method A) | |Step_Title=Add supports (Method A) | ||
|Step_Content=I used giant, 3 foot zip ties to make tension supports for the chair. Simply drilling two holes through the plywood and using a box cutter to carve out the area between the holes, I was able to create a rectangular hole large enough to strap part of the zip tie through. I then cut the head off of a second tie to cap the other end. I used the same method to make vertical supports that keep the back from reclining too far. | |Step_Content=I used giant, 3 foot zip ties to make tension supports for the chair. Simply drilling two holes through the plywood and using a box cutter to carve out the area between the holes, I was able to create a rectangular hole large enough to strap part of the zip tie through. I then cut the head off of a second tie to cap the other end. I used the same method to make vertical supports that keep the back from reclining too far. | ||
Ligne 121 : | Ligne 121 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Add supports (Method B) | |Step_Title=Add supports (Method B) | ||
|Step_Content=For the second chair, I cut some scrap plywood into supports and zip tied them to both the leg and back pieces of the chair. | |Step_Content=For the second chair, I cut some scrap plywood into supports and zip tied them to both the leg and back pieces of the chair. | ||
Ligne 131 : | Ligne 131 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Title=Tada! | |Step_Title=Tada! | ||
|Step_Content=Good luck making your own ZipStich Chair and please email or tweet photos to [http://twitter.com/benuyeda @benuyeda] or ben@homemade-modern.com. | |Step_Content=Good luck making your own ZipStich Chair and please email or tweet photos to [http://twitter.com/benuyeda @benuyeda] or ben@homemade-modern.com. | ||
Ligne 143 : | Ligne 143 : | ||
|Step_Picture_05=hmm_ep21_zipstichchair_option6.jpg | |Step_Picture_05=hmm_ep21_zipstichchair_option6.jpg | ||
}} | }} | ||
− | {{ | + | {{Notes |
|Notes=This project is also available [http://homemade-modern.com/ep21-the-zipstich-chair/ on my blog]. | |Notes=This project is also available [http://homemade-modern.com/ep21-the-zipstich-chair/ on my blog]. | ||
Watch the video tutorial of this chair [https://www.youtube.com/watch?v=2jLEsCf6iR0 on my Youtube channel] | Watch the video tutorial of this chair [https://www.youtube.com/watch?v=2jLEsCf6iR0 on my Youtube channel] | ||
}} | }} | ||
− | {{ | + | {{Tuto Status |
|Complete=Published | |Complete=Published | ||
}} | }} |
Auteur Ben Uyeda | Dernière modification 9/12/2019 par Clementflipo
Chair ZipStich Chair Final.png en none Creation 1
Chairs are generally more difficult to make than benches or stools, but here's one that can be made by stitching (or what we're calling 'stiching') plywood pieces with zip ties.
I was able to make 2 chairs out of a single 4’ by 8’ sheet of plywood. The chairs I built with ¼" thick plywood are strong, but over time the holes could wear through, so I'd recommend using ½" thick plywood. Feel free to do some experimenting with the design of the chair and share your results.
4'x 8' Sheet of 1/2” Thick Plywood. There are a lot of different types of plywood. I used ¼” plywood which is strong enough to hold my weight but might not stand the test of time. 3/8” or ½” thick plywood would provide superior durability.
Zip Ties Zip ties – also called cable ties or tie wraps – come in a variety of different sizes. I tried both large 10” ties and thinner 4” ties. The thinner ties are much easier to work with.
I used my Circular Saw with a plywood blade to make the cuts. The laser guide makes it really easy to follow the lines. If you don’t have a laser then clamp a guide to the plywood.
I measured a line 1/2” from the edges and marked an X every 1" inch down the line to indicate drill marks.
I clamped 2 to 3 boards together to drill the holes on multiple pieces at the same time.
I zipped a series of loops into the drilled holes in the first piece. Then I strung zip ties through the holes in the second piece and the zip tie loops in the first piece. This creates a zip tie to zip tie connection/link. Keep the links loose for now.
Shaping and tightening the zip ties is an incremental process that requires a bit of patience. The good news is that you can always cut and redo zip ties if you make a mistake. Use long nose pliers to tighten the ties and diagonal pliers to cut the long ends.
I used giant, 3 foot zip ties to make tension supports for the chair. Simply drilling two holes through the plywood and using a box cutter to carve out the area between the holes, I was able to create a rectangular hole large enough to strap part of the zip tie through. I then cut the head off of a second tie to cap the other end. I used the same method to make vertical supports that keep the back from reclining too far.
For the second chair, I cut some scrap plywood into supports and zip tied them to both the leg and back pieces of the chair.
Good luck making your own ZipStich Chair and please email or tweet photos to @benuyeda or ben@homemade-modern.com.
For more detailed instructions, dimensioned drawings and different variations of the project, check out our soon-to-be-released book.
This project is also available on my blog.
Watch the video tutorial of this chair on my Youtube channel
Published Published
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #