(set pageLanguageSource property) |
(update property name) |
||
Ligne 1 : | Ligne 1 : | ||
− | {{ | + | {{Tuto Details |
|Type=Creation | |Type=Creation | ||
|Area=Energy, Machines and Tools | |Area=Energy, Machines and Tools | ||
Ligne 14 : | Ligne 14 : | ||
|IsTranslation=0 | |IsTranslation=0 | ||
}} | }} | ||
− | {{ | + | {{Introduction |
|Introduction=Preparing the aluminium profiles | |Introduction=Preparing the aluminium profiles | ||
}} | }} | ||
− | {{ | + | {{Materials |
|Step_Picture_00=SunZilla_Step_01_01.jpg | |Step_Picture_00=SunZilla_Step_01_01.jpg | ||
|Step_Picture_01=SunZilla_Step_01_02.jpg | |Step_Picture_01=SunZilla_Step_01_02.jpg | ||
Ligne 43 : | Ligne 43 : | ||
* Countersinking cutter | * Countersinking cutter | ||
}} | }} | ||
− | {{ | + | {{Separator}} |
− | {{ | + | {{Tuto Step |
|Step_Picture_00=SunZilla_Step_02_01.jpg | |Step_Picture_00=SunZilla_Step_02_01.jpg | ||
|Step_Title=Cut the aluminum profiles | |Step_Title=Cut the aluminum profiles | ||
|Step_Content=Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture. | |Step_Content=Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture. | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Picture_00=SunZilla_Step_04_01.jpg | |Step_Picture_00=SunZilla_Step_04_01.jpg | ||
|Step_Picture_01=SunZilla_Step_04_02.jpg | |Step_Picture_01=SunZilla_Step_04_02.jpg | ||
Ligne 56 : | Ligne 56 : | ||
|Step_Content=Mark the position of the hole you will drill with the metal marker and the ruler. For the precise location and size of the various holes in the specific profiles, refer to the technical drawings in the below PDFs. | |Step_Content=Mark the position of the hole you will drill with the metal marker and the ruler. For the precise location and size of the various holes in the specific profiles, refer to the technical drawings in the below PDFs. | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Picture_00=SunZilla_Step_05_01.jpg | |Step_Picture_00=SunZilla_Step_05_01.jpg | ||
|Step_Picture_01=SunZilla_Step_05_02.jpg | |Step_Picture_01=SunZilla_Step_05_02.jpg | ||
Ligne 68 : | Ligne 68 : | ||
After the holes are drilled they also need to be deburred by a countersinking cutter. | After the holes are drilled they also need to be deburred by a countersinking cutter. | ||
}} | }} | ||
− | {{ | + | {{Tuto Step |
|Step_Picture_00=SunZilla_Step_07_01.jpg | |Step_Picture_00=SunZilla_Step_07_01.jpg | ||
|Step_Picture_01=SunZilla_Step_07_02.jpg | |Step_Picture_01=SunZilla_Step_07_02.jpg | ||
Ligne 80 : | Ligne 80 : | ||
These will be cut open on one side like on the first picture beside. | These will be cut open on one side like on the first picture beside. | ||
}} | }} | ||
− | {{ | + | {{Notes |
|Notes= | |Notes= | ||
}} | }} | ||
− | {{ | + | {{Tuto Status |
|Complete=Draft | |Complete=Draft | ||
}} | }} |
Auteur SunZilla | Dernière modification 9/12/2019 par Clementflipo
SunZilla_Step_07_04.jpg en none Creation 0
Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture.
Mark the position of the hole you will drill with the metal marker and the ruler. For the precise location and size of the various holes in the specific profiles, refer to the technical drawings in the below PDFs.
Afterwards, the marked positions need to be punched with the centre punch and then the holes can be drilled with the drill press.
After the holes are drilled they also need to be deburred by a countersinking cutter.
For the 4 x 150mm long square profiles, you should use the .PDF technical drawing "Folding Mech.- slides.pdf".
These will be cut open on one side like on the first picture beside.
Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #