Open Workshop Setup/de : Différence entre versions

(Page créée avec « Das Einrichten eines einfachen Werkstattbereichs um Werkzeuge und Materialien einfach und effizient zu organisieren und zu managen. »)
 
(Page créée avec « Eine organisiere Werkstatt ist Schlüsselfaktor für das aktive Arbeiten an Projekten. »)
Ligne 16 : Ligne 16 :
 
}}
 
}}
 
{{ {{tntn|Introduction}}
 
{{ {{tntn|Introduction}}
|Introduction=Creating a organised workshop is key for your active work on projects.  
+
|Introduction=Eine organisiere Werkstatt ist Schlüsselfaktor für das aktive Arbeiten an Projekten.  
  
 
So we came up with a simple and cheap way of doing it, the more materials you upcycle to build it, the more you can reduce the costs.
 
So we came up with a simple and cheap way of doing it, the more materials you upcycle to build it, the more you can reduce the costs.

Version du 6 décembre 2018 à 17:54

Auteur avatarTimm Wille | Dernière modification 27/02/2021 par Timm

Open Workshop Setup OpenWorkshopSetup-new-15.jpg
Das Einrichten eines einfachen Werkstattbereichs um Werkzeuge und Materialien einfach und effizient zu organisieren und zu managen.
Difficulté
Facile
Durée
8 heure(s)
Catégories
Électronique, Machines & Outils, Recyclage & Upcycling
Coût
100 USD ($)
Autres langues :
Deutsch • ‎English
Licence : Attribution-ShareAlike (CC BY-SA)

Introduction

Eine organisiere Werkstatt ist Schlüsselfaktor für das aktive Arbeiten an Projekten.

So we came up with a simple and cheap way of doing it, the more materials you upcycle to build it, the more you can reduce the costs.

Matériaux

  • 2x plywood (90x60cm, 90x120cm)
  • nails (100, 60, 40, 25 mm)
  • timber (for the box) + leftover plywood sheets
  • long timber (120x7cm)
  • boxes
  • water bottles (1.0 & 0.5 l)
  • solid wooden table (120x70x90cm)

Outils

  • hammer
  • saw
  • sissors
  • tape measure
  • water level
  • square
  • sandpaper
  • documentation camera/smartphone cam

Étape 1 - Space selection & preparation

  • You need a space where you can work, so at least 8x bigger than your original workshop spot
  • use a corner of the room (about 2.0x1.0m Space minimum)
  • keep lights and accessebillity in mind
  • kreate an overview of tools and materials you have
  • start looking for a good sized plywood for your tools (big) and your small materials (small)
  • use a solid table as base for the construction (at least 90cm high and 70cm deep)
  • have a powerplug close to it
  • cut the wood sheets



Étape 2 - prepare tools & materials

  • sort materials and tools by type and usage
  • cut the bottles to fill with materials (screws, bolts, nuts, washers, hooks, rivets etc.)
  • place the tools in order on the ground to the sheet (try different setups)
  • draw a fine line with a pencil around the tools
  • cut the parts for the box and the skrewdriver board and add it to the wall setup
  • nail everything to the board and remove the tools


Étape 3 - Fix the boards to the wall

  • nail the board to the wall. (you can also use screws)
  • Build up some boxes for materials like markers.
  • Draw the shapes of the materials and tools for easy identification after use.
  • fix the timber board under the board, right above the table.


Étape 4 - Fix tools and materials to the boards and finish up

  • Tools and materials should be fixed based on there shapes.
  • Balance both sides to reduce more weight on one side

Étape 5 - Tips & WATCH YOUR TOOLS

  • Always ensure the open training space is neat and clean.
  • Keep off children near the work space.
  • The work space should be dust free at all times
  • Ensure to bring back tools and materials taken from the work space.
  • Should be free from water  since some of the tools rusts.


Commentaires

Published