SunZilla - Setup manual : Différence entre versions

Version actuelle datée du 9 décembre 2019 à 11:59

This is the Sunzilla 3.0 assembly manual with Safety Instructions. This manual explains how to commission and decommission the SunZilla 3.0. and includes imporant safety information. PLEASE DO NOT ATTEMPT TO USE THE SUNZILLA 3.0 UNTIL YOU HAVE READ THIS MANUAL!

Auteur SunZilla | Dernière modification 9/12/2019 par Clementflipo

Difficulté

Facile

Durée

20 minute(s)

Catégories

Énergie

Coût

0 EUR (€)

This is the Sunzilla 3.0 assembly manual with Safety Instructions. This manual explains how to commission and decommission the SunZilla 3.0. and includes imporant safety information. PLEASE DO NOT ATTEMPT TO USE THE SUNZILLA 3.0 UNTIL YOU HAVE READ THIS MANUAL!

Difficulté

Facile

Durée

20 minute(s)

Catégories

Énergie

Coût

0 EUR (€)

Autres langues :

English

Sommaire

1 Introduction
2 Étape 1 - Connect the three boxes
3 Étape 2 - Close the solar module box
4 Étape 3 - Insert the aluminium profiles
5 Étape 4 - Pull down the elastic bands
6 Étape 5 -
7 Étape 6 -
8 Étape 7 -
9 Étape 8 - Switch on battery box
10 Étape 9 - Switch on socket box
11 Étape 10 - Plug in consumer
12 Étape 11 - Dismanteling
13 Étape 12 - Switch off Socket Box if switched on
14 Étape 13 - Turn Solar Panels out of sun
15 Étape 14 - Disconnect Solar-Connectors
16 Étape 15 - Switch off Battery box
17 Étape 16 - Unplug / detach orange cables
18 Étape 17 - Switch on Socket box again
19 Commentaires

Licence : CERN Open Hardware Licence v1.2

Sunzilla_Assembly_03.png en none Technique 0

Introduction

Technical details:

Solar peak Power: 140W
Maximum AC-output of pure sinus inverter: 350W (700W peakload)
Effectiv battery storage: 600 Wh

Matériaux

Get the three boxes : 1. The left one (A) is the battery box 2. The mid- dle one (B) the solar box 3. The right one (C) the socket box

Open the solar module box, and get the solar cells, the cables, the aluminium profiles and the 8 screws outside.

Outils

Étape 1 - Connect the three boxes

Press the cable inside when both white points match and turn the blue top unit of the cable to lock.

Étape 2 - Close the solar module box

Close the solar module box, put the two long aluminium profiles in their holes. Open slightly the box and insert two screws to lock the profiles. Choose the same holes in the middle and be sure to do the same on both sides.

Étape 3 - Insert the aluminium profiles

Take the shorter aluminium profiles, insert them as shown on the pic and lock them.

Étape 4 - Pull down the elastic bands

Étape 5 -

Take the solar cells. Unfold them and shift the aluminium edges at all four sides

Étape 6 -

Take the upper part of the solar module and connect the whole solar module with the upper aluminium profile. Be sure that the solar module is on the left side of the aluminium profile. Connect also the lower part.

Étape 7 -

Connect the cables from the solar cells to the solar module box.

Étape 8 - Switch on battery box

Switch on battery box. Green light should turn on

Étape 9 - Switch on socket box

Switch on socket box. Green light should turn on

Étape 10 - Plug in consumer

Étape 11 - Dismanteling

IMPORTANT!! DANGER!! READ DISMANTLING MANUAL!!

At Dismanteling, you MUST follow the right order of these steps, otherwise you could be hurt.

Étape 12 - Switch off Socket Box if switched on

Switch off Socket Box if switched on

Étape 13 - Turn Solar Panels out of sun

Turn Solar Panels out of sun and cover at least one Solar-Panel (for exam- ple with Pullover)

Étape 14 - Disconnect Solar-Connectors

Étape 15 - Switch off Battery box

Étape 16 - Unplug / detach orange cables

Étape 17 - Switch on Socket box again

Switch on Socket box again until green light is off (to discharge local en- ergy storage), then switch OFF again!

YOU’RE DONE!

Commentaires

Published

@@ Ligne 1 : / Ligne 1 : @@
-{{ {{tntn|Tuto Details}}
+{{Tuto Details
 |Main_Picture=Sunzilla_Assembly_03.png
 |Licences=CERN Open Hardware Licence v1.2
@@ Ligne 14 : / Ligne 14 : @@
 |IsTranslation=0
 }}
-{{ {{tntn|Introduction}}
+{{Introduction
 |Introduction=<translate><!--T:2-->
 '''Technical details:'''
@@ Ligne 21 : / Ligne 21 : @@
 * Effectiv battery storage: 600 Wh</translate>
 }}
-{{ {{tntn|Materials}}
+{{Materials
 |Step_Picture_00=Sunzilla_Assembly_01.png
 |Step_Picture_01=Sunzilla_Assembly_02.png
@@ Ligne 34 : / Ligne 34 : @@
 |Tools=<translate></translate>
 }}
-{{ {{tntn|Separator}}}}
+{{Separator}}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:5--> Connect the three boxes</translate>
 |Step_Content=<translate><!--T:6--> Press the cable inside when both white points match and turn the blue top unit of the cable to lock.</translate>
@@ Ligne 43 : / Ligne 43 : @@
 |Step_Picture_03=Sunzilla_Assembly_06.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:7--> Close the solar module box</translate>
 |Step_Content=<translate><!--T:8--> Close the solar module box, put the two long aluminium profiles in their holes. Open slightly the box and insert two screws to lock the profiles. Choose the same holes in the middle and be sure to do the same on both sides.</translate>
@@ Ligne 50 : / Ligne 50 : @@
 |Step_Picture_02=Sunzilla_Assembly_10.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:9--> Insert the aluminium profiles</translate>
 |Step_Content=<translate><!--T:10--> Take the shorter aluminium profiles, insert them as shown on the pic and lock them.</translate>
@@ Ligne 56 : / Ligne 56 : @@
 |Step_Picture_01=Sunzilla_Assembly_12.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:11--> Pull down the elastic bands</translate>
 |Step_Content=<translate></translate>
 |Step_Picture_00=Sunzilla_Assembly_13.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate></translate>
 |Step_Content=<translate><!--T:12--> Take the solar cells. Unfold them and shift the aluminium edges at all four sides</translate>
@@ Ligne 70 : / Ligne 70 : @@
 |Step_Picture_04=Sunzilla_Assembly_18.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate></translate>
 |Step_Content=<translate><!--T:13--> Take the upper part of the solar module and connect the whole solar module with the upper aluminium profile. Be sure that the solar module is on the left side of the aluminium profile. Connect also the lower part.</translate>
@@ Ligne 78 : / Ligne 78 : @@
 |Step_Picture_03=Sunzilla_Assembly_22.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate></translate>
 |Step_Content=<translate><!--T:14--> Connect the cables from the solar cells to the solar module box.</translate>
@@ Ligne 84 : / Ligne 84 : @@
 |Step_Picture_01=Sunzilla_Assembly_24.png
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:15--> Switch on battery box</translate>
 |Step_Content=<translate><!--T:16--> Switch on battery box. Green light should turn on</translate>
@@ Ligne 94 : / Ligne 94 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:17--> Switch on socket box</translate>
 |Step_Content=<translate><!--T:18--> Switch on socket box. Green light should turn on</translate>
@@ Ligne 104 : / Ligne 104 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:19--> Plug in consumer</translate>
 |Step_Content=<translate></translate>
@@ Ligne 114 : / Ligne 114 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:20--> Dismanteling</translate>
 |Step_Content=<translate><!--T:21-->
@@ Ligne 128 : / Ligne 128 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:23--> Switch off Socket Box if switched on</translate>
 |Step_Content=<translate><!--T:24--> Switch off Socket Box if switched on</translate>
@@ Ligne 138 : / Ligne 138 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:25--> Turn Solar Panels out of sun</translate>
 |Step_Content=<translate><!--T:26--> Turn Solar Panels out of sun and cover at least one Solar-Panel (for exam- ple with Pullover)</translate>
@@ Ligne 148 : / Ligne 148 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:27--> Disconnect Solar-Connectors</translate>
 |Step_Content=<translate></translate>
@@ Ligne 158 : / Ligne 158 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:28--> Switch off Battery box</translate>
 |Step_Content=<translate></translate>
@@ Ligne 168 : / Ligne 168 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:29--> Unplug / detach orange cables</translate>
 |Step_Content=<translate></translate>
@@ Ligne 178 : / Ligne 178 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Tuto Step}}
+{{Tuto Step
 |Step_Title=<translate><!--T:30--> Switch on Socket box again</translate>
 |Step_Content=<translate><!--T:31-->
@@ Ligne 193 : / Ligne 193 : @@
 |Step_Picture_05=No-image-yet.jpg
 }}
-{{ {{tntn|Notes}}
+{{Notes
 |Notes=<translate></translate>
 }}
-{{ {{tntn|Tuto Status}}
+{{Tuto Status
 |Complete=Published
 }}
 {{Separator}}