(Imported page from en.wikifab.org) |
(update property name) |
||
(5 révisions intermédiaires par 3 utilisateurs non affichées) | |||
Ligne 1 : | Ligne 1 : | ||
{{Tuto Details | {{Tuto Details | ||
− | |||
− | |||
− | |||
|Type=Creation | |Type=Creation | ||
− | |Area=Energy, | + | |Area=Energy, Machines and Tools |
|Description=This is the second tutorial for building the Pop-up Solar Generator: SunZilla 3.0. Here we are going to build the inverter and battery box | |Description=This is the second tutorial for building the Pop-up Solar Generator: SunZilla 3.0. Here we are going to build the inverter and battery box | ||
|Difficulty=Medium | |Difficulty=Medium | ||
Ligne 13 : | Ligne 10 : | ||
|Licences=Attribution (CC BY) | |Licences=Attribution (CC BY) | ||
|Main_Picture=SunZilla_Step_07_04.jpg | |Main_Picture=SunZilla_Step_07_04.jpg | ||
+ | |SourceLanguage=none | ||
+ | |Language=en | ||
+ | |IsTranslation=0 | ||
}} | }} | ||
{{Introduction | {{Introduction | ||
Ligne 18 : | Ligne 18 : | ||
}} | }} | ||
{{Materials | {{Materials | ||
+ | |Step_Picture_00=SunZilla_Step_01_01.jpg | ||
+ | |Step_Picture_01=SunZilla_Step_01_02.jpg | ||
|Material=* Black Euro-Boxes: 80€ | |Material=* Black Euro-Boxes: 80€ | ||
* 4 Solar modules (à 35 Watt): 200€ | * 4 Solar modules (à 35 Watt): 200€ | ||
Ligne 40 : | Ligne 42 : | ||
* Silicon pistol | * Silicon pistol | ||
* Countersinking cutter | * Countersinking cutter | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{Separator}} | {{Separator}} | ||
{{Tuto Step | {{Tuto Step | ||
+ | |Step_Picture_00=SunZilla_Step_02_01.jpg | ||
|Step_Title=Cut the aluminum profiles | |Step_Title=Cut the aluminum profiles | ||
|Step_Content=Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture. | |Step_Content=Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |||
− | |||
|Step_Picture_00=SunZilla_Step_04_01.jpg | |Step_Picture_00=SunZilla_Step_04_01.jpg | ||
|Step_Picture_01=SunZilla_Step_04_02.jpg | |Step_Picture_01=SunZilla_Step_04_02.jpg | ||
|Step_Picture_02=SunZilla_Step_04_03.jpg | |Step_Picture_02=SunZilla_Step_04_03.jpg | ||
− | | | + | |Step_Title=Mark hole's positions |
− | | | + | |Step_Content=Mark the position of the hole you will drill with the metal marker and the ruler. For the precise location and size of the various holes in the specific profiles, refer to the technical drawings in the below PDFs. |
− | |||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |||
− | |||
− | |||
− | |||
|Step_Picture_00=SunZilla_Step_05_01.jpg | |Step_Picture_00=SunZilla_Step_05_01.jpg | ||
|Step_Picture_01=SunZilla_Step_05_02.jpg | |Step_Picture_01=SunZilla_Step_05_02.jpg | ||
Ligne 79 : | Ligne 63 : | ||
|Step_Picture_04=SunZilla_Step_06_01.jpg | |Step_Picture_04=SunZilla_Step_06_01.jpg | ||
|Step_Picture_05=SunZilla_Step_06_02.jpg | |Step_Picture_05=SunZilla_Step_06_02.jpg | ||
+ | |Step_Title=Drill holes with the drill press | ||
+ | |Step_Content=Afterwards, the marked positions need to be punched with the centre punch and then the holes can be drilled with the drill press. | ||
+ | |||
+ | After the holes are drilled they also need to be deburred by a countersinking cutter. | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
+ | |Step_Picture_00=SunZilla_Step_07_01.jpg | ||
+ | |Step_Picture_01=SunZilla_Step_07_02.jpg | ||
+ | |Step_Picture_02=SunZilla_Step_07_03.jpg | ||
+ | |Step_Picture_03=SunZilla_Step_07_04.jpg | ||
|Step_Title=Cut open on one side | |Step_Title=Cut open on one side | ||
|Step_Content=For the 4 x 150mm long square profiles, you should use the .PDF technical drawing "Folding Mech.- slides.pdf". | |Step_Content=For the 4 x 150mm long square profiles, you should use the .PDF technical drawing "Folding Mech.- slides.pdf". | ||
− | {{Pin| | + | {{Pin| the length is incorrectly indicated as 200mm in the technical drawing.}} |
These will be cut open on one side like on the first picture beside. | These will be cut open on one side like on the first picture beside. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
− | {{Notes}} | + | {{Notes |
+ | |Notes= | ||
+ | }} | ||
+ | {{Tuto Status | ||
+ | |Complete=Draft | ||
+ | }} |
Auteur SunZilla | Dernière modification 9/12/2019 par Clementflipo
SunZilla_Step_07_04.jpg en none Creation 0
Cut the aluminum profiles according to the technical drawings in the attached PDFs. Once you have them in hand, the first step is to file the ends of the profiles to deburr them, as shown in the picture.
Mark the position of the hole you will drill with the metal marker and the ruler. For the precise location and size of the various holes in the specific profiles, refer to the technical drawings in the below PDFs.
Afterwards, the marked positions need to be punched with the centre punch and then the holes can be drilled with the drill press.
After the holes are drilled they also need to be deburred by a countersinking cutter.
For the 4 x 150mm long square profiles, you should use the .PDF technical drawing "Folding Mech.- slides.pdf".
These will be cut open on one side like on the first picture beside.
Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #