| Line 9: | Line 9: | ||
|Duration-type=heure(s) | |Duration-type=heure(s) | ||
|Licences=GNU Free Hardware Designs | |Licences=GNU Free Hardware Designs | ||
| − | |Main_Picture= | + | |Main_Picture=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Final.jpg |
}} | }} | ||
{{Introduction}} | {{Introduction}} | ||
| Line 19: | Line 19: | ||
{{Separator}} | {{Separator}} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Picture_00= | + | |Step_Picture_00=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1a.png |
| − | |Step_Picture_01= | + | |Step_Picture_01=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1b.png |
| − | |Step_Picture_02= | + | |Step_Picture_02=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1c.png |
| − | |Step_Picture_03= | + | |Step_Picture_03=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1d.png |
| − | |Step_Picture_04= | + | |Step_Picture_04=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1e.png |
| − | |Step_Picture_05= | + | |Step_Picture_05=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step1f.png |
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Picture_00= | + | |Step_Picture_00=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2a.png |
| − | |Step_Picture_01= | + | |Step_Picture_01=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2b.png |
| − | |Step_Picture_02= | + | |Step_Picture_02=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2c.png |
| − | |Step_Picture_03= | + | |Step_Picture_03=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2d.png |
| − | |Step_Picture_04= | + | |Step_Picture_04=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2e.png |
| − | |Step_Picture_05= | + | |Step_Picture_05=PiKon_télescope_imprimé_en_3D_et_un_Raspberry_Pi_camera_PiKon_Step2f.png |
}} | }} | ||
{{Notes}} | {{Notes}} | ||
{{Tuto Status}} | {{Tuto Status}} | ||
Revision as of 15:44, 18 August 2016
Télescope imprimé en 3D et un Raspberry Pi camera
Difficulty
⧼wf-propertyvalue-difficulty-Moyen⧽
Duration
3 ⧼wf-propertyvalue-durationtype-heure(s)⧽
Categories
⧼wf-propertyvalue-area-Science & Biologie⧽, ⧼wf-propertyvalue-area-Électronique⧽
Cost
100 GBP (£)
Contents
Step 1 -
Step 2 -
Français
English
Deutsch
Español
Italiano
Português