The duplicator must first have its memory cleared by pressing buttons A and B in a specific Instructions for Use Warning! Use a paper clip or small object to pry up the rubber cover. Use a screw to lever the cover as the figure below shows. See tableSet CODING THE REMOTE CONTROL The remote control has a unique code programmed at the factory, but it is possible to change it manually using the following procedureStep-by-Step Guide to Cloning a MHz Remote. The duplicator usesCR batteries, has a transmit distance of m, and can copy codes from original remote controls by pressing a button on each simultaneously until the LED flashes steadily. Set the DIPs combination of your How to CloneRemove the protective rubber, which gives access to the DIP switchesSelect the DIP Switches combination for the brand you want to clone. Check that the frequency of the remote control to be cloned is Mhz. Instructions for copying the remote controlReset the Code Press and hold the A and B buttons simultaneously forseconds. Follow these simple steps to clone your MHz remote: Locate the cloning button on your MHz cloning remote. See Chart BelowThe remote is ready to be used, please refer to your receiver's user manual This document provides instructions for cloning universal remote controls using a mhz duplicator. Instructions for copying the remote controlReset the Code. In fact I have consistently used rolling code clone remotes to copy other remotes. Works fine as long as all those cloning are rolling code. Locate the selector switch underneath the front cover. I copy the transmitter used to open the gate but do so out of range of the receiver. to expose the selector switchSet your selector switch for the desired manufacture. Please don't be telling people it doesn't work because I have cloned dozens of rolling code Insert the battery into the cloning remote and turn it on. This is usually located on the back or side of the device. Press and hold the cloning button until the LED light on the remote Locate the selector switch in the back of the remote. The LED will light uptimes and then it will flash Learn how to clone, copy, duplicate or replace your garage door remote control at Garage Door Nation! The LED will light uptimes and then it Yes it is possible. Programming Instructions. s and hold the A and B buttons simultaneously forseconds. The product cannot be synchronized with “rolling code” remote controls.
The duplicator must first have its memory cleared by pressing buttons A and B in a specific Instructions for Use Warning! Use a paper clip or small object to pry up the rubber cover. Use a screw to lever the cover as the figure below shows. See tableSet CODING THE REMOTE CONTROL The remote control has a unique code programmed at the factory, but it is possible to change it manually using the following procedureStep-by-Step Guide to Cloning a MHz Remote. The duplicator usesCR batteries, has a transmit distance of m, and can copy codes from original remote controls by pressing a button on each simultaneously until the LED flashes steadily. Set the DIPs combination of your How to CloneRemove the protective rubber, which gives access to the DIP switchesSelect the DIP Switches combination for the brand you want to clone. Check that the frequency of the remote control to be cloned is Mhz. Instructions for copying the remote controlReset the Code Press and hold the A and B buttons simultaneously forseconds. Follow these simple steps to clone your MHz remote: Locate the cloning button on your MHz cloning remote. See Chart BelowThe remote is ready to be used, please refer to your receiver's user manual This document provides instructions for cloning universal remote controls using a mhz duplicator. Instructions for copying the remote controlReset the Code. In fact I have consistently used rolling code clone remotes to copy other remotes. Works fine as long as all those cloning are rolling code. Locate the selector switch underneath the front cover. I copy the transmitter used to open the gate but do so out of range of the receiver. to expose the selector switchSet your selector switch for the desired manufacture. Please don't be telling people it doesn't work because I have cloned dozens of rolling code Insert the battery into the cloning remote and turn it on. This is usually located on the back or side of the device. Press and hold the cloning button until the LED light on the remote Locate the selector switch in the back of the remote. The LED will light uptimes and then it will flash Learn how to clone, copy, duplicate or replace your garage door remote control at Garage Door Nation! The LED will light uptimes and then it Yes it is possible. Programming Instructions. s and hold the A and B buttons simultaneously forseconds. The product cannot be synchronized with “rolling code” remote controls.
Français
English
Deutsch
Español
Italiano
Português