Voir la source de Entryway catch-all table

{{Tuto Details
|SourceLanguage=en
|Language=en
|IsTranslation=0
|Type=Creation
|Area=Decoration, Furniture, House
|Description=We needed a place to organize our stuff where we walk into our house. This entryway catch-all sideboard is the first, of a few, that will help solve our problem.
|Difficulty=Medium
|Cost=50
|Currency=USD ($)
|Duration=5
|Duration-type=hour(s)
|Licences=Attribution (CC BY)
|Main_Picture=Entry way catch all table cabinet Final.jpg
}}
{{Introduction}}
{{Materials}}
{{Separator}}
{{Tuto Step
|Step_Content=I started with a full sheet of Maple plywood. I broke it down into manageable chunks using my track saw.
|Step_Picture_00=Entry way catch all table cabinet 01.jpg
}}
{{Tuto Step
|Step_Title=Cut to the rough dimensions
|Step_Content=Then I cut to the rough dimensions on my table saw.
|Step_Picture_00=Entry way catch all table cabinet 02.jpg
}}
{{Tuto Step
|Step_Title=Cover up the plywood lines
|Step_Content=To cover up the plywood lines, I ripped some thin strips of maple hardwood. Here I'm applying the glue to adhere the strips.
|Step_Picture_00=Entry way catch all table cabinet 03.jpg
}}
{{Tuto Step
|Step_Title=Attaching the strips
|Step_Content=...and now actually attaching the strips. I "clamp" them on using some painters tape.
|Step_Picture_00=Entry way catch all table cabinet 04.jpg
}}
{{Tuto Step
|Step_Title=Trim the strips using a router.
|Step_Content=I live the strips a little wider than 3/4 of an inch so that they are slightly proud of the plywood. Then I trim them flush using a router.
|Step_Picture_00=Entry way catch all table cabinet 05.jpg
}}
{{Tuto Step
|Step_Title=Find tune everything
|Step_Content=Now that the rough pieces are created, I find tune everything to finished dimensions and cut in some joinery. Here I'm making miters on the edges of all of the case pieces. 

On the second picture I'm cutting in rabbets to the backs of the pieces so that I can eventually inset the back panel.
|Step_Picture_00=Entry way catch all table cabinet 06.jpg
|Step_Picture_01=Entry way catch all table cabinet 07.jpg
}}
{{Tuto Step
|Step_Title=Cut a few grooves
|Step_Content=Then I cut a few grooves into the front of all of the pieces to hold some sliding doors.
|Step_Picture_00=Entry way catch all table cabinet 08.jpg
}}
{{Tuto Step
|Step_Title=Cut in a dado to the top and bottom piece
|Step_Content=Finally I cut in a dado to the top and bottom piece to eventually insert a vertical partition. I use a router and then square up the cut using a chisel.
|Step_Picture_00=Entry way catch all table cabinet 09.jpg
}}
{{Tuto Step
|Step_Title=Case assembly
|Step_Content=With every thing made, i assembled the case. I used a couple dominoes to make assembly easier and provide a bit of reinforcement.
|Step_Picture_00=Entry way catch all table cabinet 10.jpg
}}
{{Tuto Step
|Step_Title=Make the doors
|Step_Content=Here I'm making the doors fro the case out of 1/4" maple plywood. They don't have any handles, just a little negative space for a finger to grab.
|Step_Picture_00=Entry way catch all table cabinet 11.jpg
}}
{{Tuto Step
|Step_Title=Frame
|Step_Content=With the cabinet out of the way I turned my attention to the frame. First I milled and cut out blanks for all of the pieces. These are made from Walnut hardwood.
|Step_Picture_00=Entry way catch all table cabinet 12.jpg
}}
{{Tuto Step
|Step_Title=Cutting a long taper on the bandsaw.
|Step_Content=You can see I'm a big proponent of marking the hell out of things. Trying to avoid mistakes...thought I still make them.
|Step_Picture_00=Entry way catch all table cabinet 13.jpg
|Step_Picture_01=Entry way catch all table cabinet 14.jpg
}}
{{Tuto Step
|Step_Title=Joinery
|Step_Content=Then with all of the pieces to their proper dimensions I cut in some joinery, and some dados to hold the shelves.
|Step_Picture_00=Entry way catch all table cabinet 15.jpg
}}
{{Tuto Step
|Step_Title=Glue and assemble everything
|Step_Content=Then I glued and assembled everything. 

Lots of assembly
|Step_Picture_00=Entry way catch all table cabinet 16.jpg
|Step_Picture_01=Entry way catch all table cabinet 17.jpg
|Step_Picture_02=Entry way catch all table cabinet 18.jpg
|Step_Picture_03=Entry way catch all table cabinet 19.jpg
}}
{{Tuto Step
|Step_Title=Sand everything
|Step_Content=Then I sanded everything.
|Step_Picture_00=Entry way catch all table cabinet 20.jpg
}}
{{Tuto Step
|Step_Title=Finished
|Step_Content=Then I varnished everything
|Step_Picture_00=Entry way catch all table cabinet 21.jpg
}}
{{Tuto Step
|Step_Title=Tada!
|Step_Content=This [https://www.youtube.com/watch?v=TjflF2hCdrQ youtube video] takes you through the design and build process.

It includes detailed builds, design-talk, 3D modeling, and more. Don't forget to subscribe!
|Step_Picture_00=Entry way catch all table cabinet final2.jpg
|Step_Picture_01=Entry way catch all table cabinet final1.jpg
}}
{{Notes
|Notes=* Check out my projects on my website : http://www.foureyesfurniture.com/
}}
{{Tuto Status
|Complete=Check this box when the tutorial is complete
}}