Voir la source de Iso 16750 5 pdf

{{Tuto Details
|Licences=Attribution (CC BY)
|Description=<translate><p><center><b>Iso 16750 5 pdf</b></p>
<p>Rating: 4.7 / 5 (8134 votes)</p>
<p>Downloads: 21674</p>
<p>CLICK HERE TO DOWNLOAD>>>https://danuz.hkjhsuies.com.es/qz7Brp?keyword=iso+16750+5+pdf</p></center>
<br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>
<p>standard by international organization for standardization,.  this second edition cancels and replaces the first edition ( iso: ), which has been technically revised.  this pdf file may contain embedded typefaces.  [ 1] iso 16750 has five parts:.  integrating and harmonizing contents from iso: ( e.  iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: ⎯ part 1: general ⎯ part 2: electrical loads.  view all product details.  iso: describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on/ in the road vehicle.  the main changes are as follows: — integration and harmonization of contents from iso: iso 16750 5 pdf ( e.  constitutes following references, requirements of document.  every requirement class is determined by a specific code letter.  for iso 16750 5 pdf each load type, several requirement classes are defined.  decrease the supply voltage from the minimum supply voltage, usmin, to 0 v, then increase it from 0 v to usmin, applying a change rate of ( 0, 5 ± 0, 1) v/ min linear, or in equal steps of not more than 25 mv.  it is not intended for direct application to parts or assemblies that are part of the equipment.  iso 16750, road vehicles – environmental conditions and testing for electrical and electronic equipment, is a series of iso standards which provide guidance regarding environmental conditions commonly encountered by electrical and electronic systems installed in automobiles and specify requirements and tests.  this part of iso 16750 applies to electrical and electronical systems/ components for road vehicles.  this document has been replaced.  the main changes are as follows: — integrating and harmonizing contents from iso: ( e.  failure mode is mechanical damage ( e.  this document applies to electric and electronic systems and components for vehicles including electric propulsion systems and components with maximum working voltages according to voltage class b.  iso: applies to electrical and electronic systems/ components for road vehicles.  the load occurs on closures when slammed shut.  this third edition cancels and replaces the second edition ( iso: ), which has been technically revised.  in references, such a way ( all parts), referenced document ( including or amendments) road road vehicles — fuse- links vehicles — environmental conditions and testing for electrical and electronic equipment iso:, — part 1: equipment — part 4.  this test checks the dut for malfunctions and breakage caused by shock of door slamming.  it does not cover electromagnetic compatibility ( emc).  isowas prepared by technical committee iso/ tc 22, road vehicles, subcommittee sc 3, electrical and electronic equipment.  it describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on.  apply the following test simultaneously to all applicable inputs ( connections) of the dut.  ⎯ part 2: electrical loads.  iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: part 1: general part 2: electrical loads.  change of table 2) ; — reorganization of test conditions and application methods in context ( 4.  view the most recent version.  this part of iso 16750 specifies the chemical loads that can affect electric and electronic systems and components in respect of their mounting location on or in road vehicles, and specifies the corresponding tests and requirements.  for example, the iso 16750 series should not be.  in accordance with adobe' s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which pdf are embedded are licensed to and installed on the computer performing the editing.  iso: ( e) the concept of the iso 16750 series is to define requirement classes for separate load types.  this document was prepared by technical committee iso/ tc 22, road vehicles, subcommittee sc 32, electrical and electronic components and general system aspects.  this fourth edition cancels and replaces the third edition ( iso: ), which has been technically revised.  the iso 16750 series describes environmental conditions and tests to be applied to electrical and electronic equipment directly mounted in or on the vehicle.  this part of iso 16750 describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on/ in the road vehicle.  ⎯ part 4: climatic loads.  the main changes are as follows:?  iso: ( e) pdf disclaimer.  it distinguishes between electrical, mechanical, thermal, climatic and chemical loads.  change of table 2 ) ;.  2 normative references.  road vehicles - environmental conditions and testing for electrical and electronic equipment - part 5: chemical loads.  ⎯ part 3: mechanical loads.  it is applicable to environmental conditions and tests affecting electrical and electronic equipment mounted directly on or in the vehicle.  iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: — part 1: general — part 2: electrical loads — part 3: mechanical loads — part 4: climatic loads — part 5: chemical loads.  iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: ⎯ part 1: general.  iso: specifies chemical loads and corresponding tests and requirements for the mounting of electric and electronic systems and components on road vehicles.  a detached capacitor inside the housing of an electronic control module due to the high accelerations caused by door slamming).  12) ; — subdivision of test methods in temperature cycle test for application to duts of  small and.</p></translate>
|Area=Electronics, Energy, Furniture, Play and Hobbies, Robotics
|Type=Technique
|Difficulty=Very easy
|Duration=928
|Duration-type=hour(s)
|Cost=785
|Currency=USD ($)
}}
{{Introduction
|Introduction=<translate></translate>
}}
{{Materials
|Material=<translate></translate>
|Tools=<translate></translate>
}}
{{Tuto Step
|Step_Title=<translate></translate>
|Step_Content=<translate></translate>
}}
{{Notes
|Notes=<translate></translate>
}}
{{PageLang
|SourceLanguage=none
|IsTranslation=0
|Language=en
}}
{{Tuto Status
|Complete=Published
}}