Voir la source de Water Bottle fan

{{ {{tntn|Tuto Details}}
|Main_Picture=Water_Bottle_fan_final-product.jpg
|Licences=Attribution-ShareAlike (CC BY-SA)
|Description=<translate><!--T:1-->
A group of young innovators from six hubs across (Media Organizations) East African Countries of South Sudan, Uganda and Kenya  came together for ASKnet Training in Adjumani district of Uganda for 14 days in October, 2019. The training was conducted by r0g Agency for open culture and critical transformation through the financial  support from  German Federal Ministry for Economic Cooperation and Development.

<!--T:2-->
During the practical part of the training, this group came up with an idea of building a  bottle water fan from scratch.
Before we started, the team list the materials and tools needed to complete the project, and where collected in one place.
Take your time to pass through all the processes as documented below</translate>
|Area=Electronics, Recycling and Upcycling
|Type=Creation
|Difficulty=Medium
|Duration=2
|Duration-type=hour(s)
|Cost=2
|Currency=USD ($)
|Tags=bottle, upcycling, fan, DIY
|SourceLanguage=none
|Language=en
|IsTranslation=0
}}
{{ {{tntn|Introduction}}
|Introduction=<translate><!--T:3--> pictures CC-BY 4.0 Vuga William</translate>
}}
{{ {{tntn|Materials}}
|Material=<translate><!--T:4-->
An empty bottle of water (500ml)

<!--T:5-->
Super glue

<!--T:6-->
Seal tape

<!--T:7-->
Marker pen

<!--T:8-->
Switch

<!--T:9-->
Wires

<!--T:10-->
Mortar

<!--T:11-->
Battery

<!--T:12-->
Soldering wires</translate>
|Tools=<translate><!--T:13-->
Scissor

<!--T:14-->
Soldering gun

<!--T:15-->
Multi-Meter

<!--T:16-->
Sucker</translate>
|ExternalAttachmentsLinks={{ {{tntn|ExternalAttachmentsLinks}}
|ExternalAttachmentsLinks=https://github.com/ASKnet-Open-Training/WaterBottleFan
}}
}}
{{ {{tntn|Separator}}}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate><!--T:17--> Tools and Materials</translate>
|Step_Content=<translate><!--T:18--> Before we started, the team list the materials and tools needed to complete the project, and where collected in one place.</translate>
|Step_Picture_00=Water_Bottle_fan_Tools_and_Materials2.jpg
|Step_Picture_01=Water_Bottle_fan_Tools_and_Materials.jpg
}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate><!--T:19--> Two Empty Bottles of  water</translate>
|Step_Content=<translate><!--T:20-->
One for erecting the fan and other for making the propeller and switch holder

<!--T:21-->
A  hole was cut on a bottle with some water inside to place the mortar on it.</translate>
|Step_Picture_00=Empty Bottles of Water.jpg
}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate><!--T:22--> Swich</translate>
|Step_Content=<translate><!--T:23-->
There was an idea to put a switch on the fan.

<!--T:24-->
For switching on and off the fan

<!--T:25-->
One more bottle was cut and attached with a switch</translate>
|Step_Picture_00=Switch and The Holder.jpg
}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Wire</translate>
|Step_Content=<translate>was used for connecting wires</translate>
|Step_Picture_00=Water_Bottle_fan_Wire.jpg
}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Soldering gun and soldering wire</translate>
|Step_Content=<translate>Soldering gun for soldering the wire on the switch and soldering wire help in connection, for sealing wire on the switch.</translate>
|Step_Picture_00=Soldering_Gun.jpg
|Step_Picture_01=Soldering_Wire.jpg
}}
{{ {{tntn|Tuto Step}}
|Step_Title=<translate>Supper Glue</translate>
|Step_Content=<translate>Gluing anything on the bottle</translate>
|Step_Picture_00=Supper_Glue.jpg
}}
{{ {{tntn|Notes}}
|Notes=<translate></translate>
}}
{{ {{tntn|Tuto Status}}
|Complete=Published
}}