Voir la source de SolarOSE - Guide 4: Skeleton of the receiver

{{Tuto Details
|SourceLanguage=none
|Language=en
|IsTranslation=0
|Type=Creation
|Area=Energy
|Description=<translate>This is the second tutorial for building the solar concentrator of Open Source Ecologie (French branch of Open Source Ecology). Here we are going to build the mirror facets.</translate>
|Difficulty=Medium
|Cost=100
|Currency=EUR (€)
|Duration=3
|Duration-type=hour(s)
|Licences=Attribution-ShareAlike (CC BY-SA)
|Main_Picture=SolarOSE_G4_4_1.jpg
}}
{{Introduction|}}
{{Separator}}
{{Materials
|Step_Picture_01=No-image-yet.jpg
|Step_Picture_02=No-image-yet.jpg
|Step_Picture_03=No-image-yet.jpg
|Step_Picture_04=No-image-yet.jpg
|Step_Picture_05=No-image-yet.jpg
}}
{{Separator}}
{{Tuto Step
|Step_Title=<translate>Main beam</translate>
|Step_Content=<translate>Cut the 30x30x2300 mm square tube.
Drill the fixation holes of the tepee. Drill and tap at 5 mm diameter the fixation holes of the junction.</translate>
|Step_Picture_00=SolarOSE_G4_1_1.jpg
|Step_Picture_01=No-image-yet.jpg
|Step_Picture_02=No-image-yet.jpg
|Step_Picture_03=No-image-yet.jpg
|Step_Picture_04=No-image-yet.jpg
|Step_Picture_05=No-image-yet.jpg
}}
{{Tuto Step
|Step_Title=<translate>Lateral 'L' profiles</translate>
|Step_Content=<translate>Cut two L profiles 30x60 mm, thick of 3 mm and long of 2100 mm.

Drill and tap the fixation holes of the exterior cover, screw with a diameter 4 mm.

Drill the fixation holes at the junction, as depicted in the 3D model. Improvement: drill 2 holes on the side and none on the bottom of the L.

Weld a flat at each edge of the L (for the fixation on the “tepee”…).</translate>
|Step_Picture_00=SolarOSE_G4_2_1.jpg
|Step_Picture_01=No-image-yet.jpg
|Step_Picture_02=No-image-yet.jpg
|Step_Picture_03=No-image-yet.jpg
|Step_Picture_04=No-image-yet.jpg
|Step_Picture_05=No-image-yet.jpg
}}
{{Tuto Step
|Step_Title=<translate>Junction of the main beam and the lateral L profiles</translate>
|Step_Content=<translate>Cut, drill, weld according to the 3D model.</translate>
|Step_Picture_00=SolarOSE_G4_3_1.jpg
|Step_Picture_01=SolarOSE_G4_3_2.jpg
|Step_Picture_02=No-image-yet.jpg
|Step_Picture_03=No-image-yet.jpg
|Step_Picture_04=No-image-yet.jpg
|Step_Picture_05=No-image-yet.jpg
}}
{{Tuto Step
|Step_Title=<translate>Hanger</translate>
|Step_Content=<translate>Print the 10 hangers at the cutting laser. The material used is a wood board (for example laminated structural wood) with a thickness of 10 mm.

Cut shapes of 2 hangers (with a cutting laser or manually), without emptying them. They are needed for the secondary reflector in order to close the receiver on its edges.

Link to the file for printing!</translate>
|Step_Picture_00=SolarOSE_G4_4_1.jpg
|Step_Picture_01=SolarOSE G4 4 2.jpg
|Step_Picture_02=SolarOSE G4 4 3.jpg
|Step_Picture_03=No-image-yet.jpg
|Step_Picture_04=No-image-yet.jpg
|Step_Picture_05=No-image-yet.jpg
}}
{{Notes|}}