Voir la source de Open Workshop Setup/en

{{Tuto Details
|Main_Picture=Open_Workshop_Setup_OpenWorkshopSetup-new-15.jpg
|Licences=Attribution-ShareAlike (CC BY-SA)
|Description=Create a simple workspace setup to manage and organise your tools and materials.
|Area=Electronics, Machines and Tools, Recycling and Upcycling
|Type=Creation
|Difficulty=Easy
|Duration=8
|Duration-type=hour(s)
|Cost=100
|Currency=USD ($)
|Tags=Workshop, Tools, Materials, Open Source Hardware, Management
|SourceLanguage=none
|Language=en
|IsTranslation=1
}}
{{Introduction
|Introduction=Creating a organised workshop is key for your active work on projects. 

So we came up with a simple and cheap way of doing it, the more materials you upcycle to build it, the more you can reduce the costs.
}}
{{Materials
|Step_Picture_00=Open_Workshop_Setup_OpenWorkshopSetup-new-7.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-4.jpg
|Step_Picture_02=Open_Workshop_Setup_OpenWorkshopSetup-new-1.jpg
|Material=* 2x plywood (90x60cm, 90x120cm)
* nails (100, 60, 40, 25 mm)
* timber (for the box) + leftover plywood sheets
* long timber (120x7cm)
* boxes
* water bottles (1.0 & 0.5 l)
* solid wooden table (120x70x90cm)
|Tools=* hammer
* saw
* sissors
* tape measure 
* water level
* square
* sandpaper
* documentation camera/smartphone cam
}}
{{Separator}}
{{Tuto Step
|Step_Title=Space selection & preparation
|Step_Content=* You need a space where you can work, so at least 8x bigger than your original workshop spot
* use a corner of the room (about 2.0x1.0m Space minimum)
* keep lights and accessebillity in mind
* kreate an overview of tools and materials you have
* start looking for a good sized plywood for your tools (big) and your small materials (small)
* use a solid table as base for the construction  (at least 90cm high and 70cm deep)
* have a powerplug close to it
* cut the wood sheets
|Step_Picture_00=Open_Workshop_Setup_Workspace-sketch.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-22.jpg
}}
{{Tuto Step
|Step_Title=prepare tools & materials
|Step_Content=* sort materials and tools by type and usage
* cut the bottles to fill with materials (screws, bolts, nuts, washers, hooks, rivets etc.)
* place the tools in order on the ground to the sheet (try different setups)
* draw a fine line with a pencil around the tools
* cut the parts for the box and the skrewdriver board and add it to the wall setup
* nail everything to the board and remove the tools
|Step_Picture_00=Open_Workshop_Setup_OpenWorkshopSetup-new-6.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-9.jpg
|Step_Picture_02=Open_Workshop_Setup_OpenWorkshopSetup-new-10.jpg
|Step_Picture_03=Open_Workshop_Setup_OpenWorkshopSetup-new-8.jpg
}}
{{Tuto Step
|Step_Title=Fix the boards to the wall
|Step_Content=* nail the board to the wall. (you can also use screws) 

* Build up some boxes for materials like markers.

* Draw the shapes of the materials and tools for easy identification after use.
* fix the timber board under the board, right above the table.
|Step_Picture_00=Open_Workshop_Setup_OpenWorkshopSetup-new-5.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-13.jpg
|Step_Picture_02=Open_Workshop_Setup_OpenWorkshopSetup-new-14.jpg
|Step_Picture_03=Open_Workshop_Setup_OpenWorkshopSetup-new-12.jpg
}}
{{Tuto Step
|Step_Title=Fix tools and materials to the boards and finish up
|Step_Content=* Tools and materials should be fixed based on there shapes.

* Balance both sides to reduce more weight on one side
|Step_Picture_00=Open_Workshop_Setup_OpenWorkshopSetup-new-18.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-17.jpg
|Step_Picture_02=Open_Workshop_Setup_OpenWorkshopSetup-new-20.jpg
|Step_Picture_03=Open_Workshop_Setup_OpenWorkshopSetup-new-25.jpg
|Step_Picture_04=Open_Workshop_Setup_OpenWorkshopSetup-new-26.jpg
}}
{{Tuto Step
|Step_Title=Tips & WATCH YOUR TOOLS
|Step_Content=* Always ensure the open training space is neat and clean.

* Keep off children near the work space.

* The work space should be dust free at all times

* Ensure to bring back tools and materials taken from the work space. 

* Should be free from water  since some of the tools rusts.
|Step_Picture_00=Open_Workshop_Setup_OpenWorkshopSetup-new-24.jpg
|Step_Picture_01=Open_Workshop_Setup_OpenWorkshopSetup-new-23.jpg
|Step_Picture_02=Open_Workshop_Setup_OpenWorkshopSetup-new-19.jpg
|Step_Picture_03=Open_Workshop_Setup_OpenWorkshopSetup-new-27.jpg
}}
{{Notes
|Notes=
}}
{{Tuto Status
|Complete=Published
}}