Is it possible to replace the WR3 module with an ESP-12 module : Différence entre versions

Version actuelle datée du 14 octobre 2021 à 23:03

In this Documentation I am showing what I was able to find out about the MiBoxer WL5 5 in 1 WiFi RGB+CCT Controller.

Auteur Sarius8e | Dernière modification 14/10/2021 par Sarius8e

Difficulté

Moyen

Durée

20 minute(s)

Catégories

Électronique

Coût

15 EUR (€)

In this Documentation I am showing what I was able to find out about the MiBoxer WL5 5 in 1 WiFi RGB+CCT Controller.

Difficulté

Moyen

Durée

20 minute(s)

Catégories

Électronique

Coût

15 EUR (€)

Sommaire

1 Introduction
2 Étape 1 - The PCB on which the Tuya WR3 module is soldered on.
3 Étape 2 - The Top and bottom side of the whole PCB.
4 Commentaires

Creation

Introduction

I ordered a RGB+CCT controller online and to my surprise the device came with a new Tuya WiFi module instead of an ESP module.

Now I am trying to swap the WR3 Tuya WiFi module with an ESP-12f module.

In the following steps I will display my findings.

Matériaux

Outils

Étape 1 - The PCB on which the Tuya WR3 module is soldered on.

I desoldered the WR3 module to check the connections with my meter and also used a lamp to expose the traces.

I checked the conenctions and it seems that only RX, TX , VCC, GND and EN are connected.

I found this thread, but still do not know how to connect it properly.

I will figure out the software side.

https://github.com/arendst/Tasmota/issues/7385

The ESP is used with Tasmota installed and communicates with the IC over serial.

Étape 2 - The Top and bottom side of the whole PCB.

This shows the top and bottom side

Commentaires

en none 0 Published

@@ Ligne 1 : / Ligne 1 : @@
 {{Tuto Details
+|Main_Picture=Is_it_possible_to_replace_the_WR3_module_with_an_ESP-12_module_1_WiFi_module_WL5.jpg
+|Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-28,"top":39,"width":3543,"height":2362,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.18,"scaleY":0.18,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://wikifab.org/images/8/8d/Is_it_possible_to_replace_the_WR3_module_with_an_ESP-12_module_1_WiFi_module_WL5.jpg","filters":[]}],"height":450.33860045146724,"width":600}
 |Description=<translate>In this Documentation I am showing what I was able to find out about the MiBoxer WL5 5 in 1 WiFi RGB+CCT Controller.</translate>
 |Area=Electronics
@@ Ligne 20 : / Ligne 22 : @@
 {{Tuto Step
 |Step_Title=<translate>The PCB on which the Tuya WR3 module is soldered on.</translate>
-|Step_Content=<translate>I desoldered the WR3 module to check the connections with my meter and also used a lamp to expose the traces.</translate>
+|Step_Content=<translate>I desoldered the WR3 module to check the connections with my meter and also used a lamp to expose the traces.
+I checked the conenctions and it seems that only RX, TX , VCC, GND and EN are connected.
+I found this thread, but still do not know how to connect it properly.
+I will figure out the software side.
+https://github.com/arendst/Tasmota/issues/7385
+The ESP is used with Tasmota installed and communicates with the IC over serial.<br /></translate>
 |Step_Picture_00=Is_it_possible_to_replace_the_WR3_module_with_an_ESP-12_module_1_WiFi_module.jpg
 }}
@@ Ligne 37 : / Ligne 52 : @@
 }}
 {{Tuto Status
-|Complete=Draft
+|Complete=Published
 }}