(set pageLanguageSource property) |
|||
Line 1: | Line 1: | ||
{{ {{tntn|Tuto Details}} | {{ {{tntn|Tuto Details}} | ||
− | | | + | |Main_Picture=SolarOSE_G1_4_1.jpg |
− | | | + | |Licences=Attribution-ShareAlike (CC BY-SA) |
− | | | + | |Description=<translate>This is the first tutorial for building the [[SolarOSE_-_Solar_concentrator_for_steam_generation|solar concentrator]] of [[User:Open_Source_Écologie|Open Source Ecologie]] (French branch of [http://opensourceecology.org/ Open Source Ecology]). Here we are going to build the main structure of the mirror field.</translate> |
+ | |Area=Energy | ||
|Type=Creation | |Type=Creation | ||
− | |||
− | |||
|Difficulty=Medium | |Difficulty=Medium | ||
+ | |Duration=2 | ||
+ | |Duration-type=day(s) | ||
|Cost=2000 | |Cost=2000 | ||
|Currency=EUR (€) | |Currency=EUR (€) | ||
− | | | + | |SourceLanguage=none |
− | | | + | |Language=en |
− | | | + | |IsTranslation=0 |
− | |||
}} | }} | ||
{{ {{tntn|Introduction}} | {{ {{tntn|Introduction}} | ||
|Introduction=<translate>The support is made of two frames: repeat or double the steps 1 to 6, afterwards finish the assembling with the step 7.</translate> | |Introduction=<translate>The support is made of two frames: repeat or double the steps 1 to 6, afterwards finish the assembling with the step 7.</translate> | ||
}} | }} | ||
− | |||
{{ {{tntn|Materials}} | {{ {{tntn|Materials}} | ||
|Material=<translate>* 2 main square tubes 25x25 mm | |Material=<translate>* 2 main square tubes 25x25 mm | ||
Line 28: | Line 27: | ||
* Wood board | * Wood board | ||
* Mirror sheet</translate> | * Mirror sheet</translate> | ||
− | |Tools=* Hack saw | + | |Tools=<translate>* Hack saw |
* Grinder | * Grinder | ||
* Drilling machine | * Drilling machine | ||
* Bristol paper | * Bristol paper | ||
* Printer/laser cutting | * Printer/laser cutting | ||
− | * Adhesive tape | + | * Adhesive tape</translate> |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
− | {{Separator}} | + | {{ {{tntn|Separator}}}} |
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
|Step_Title=<translate>Cutting the square tubes</translate> | |Step_Title=<translate>Cutting the square tubes</translate> | ||
|Step_Content=<translate>Use the grinder to cut at the length of 2130 mm the two main squared tubes and at the length of 1430 mm the 2 square tubes for the support.</translate> | |Step_Content=<translate>Use the grinder to cut at the length of 2130 mm the two main squared tubes and at the length of 1430 mm the 2 square tubes for the support.</translate> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
Line 64: | Line 51: | ||
Use a pillar drill with a diameter of 6 mm. The drill should be long enough to drill the square tube on the both sides. Attention, if the tube has a welding point on the interior side, make sure not to drill there while making the second hole.</translate> | Use a pillar drill with a diameter of 6 mm. The drill should be long enough to drill the square tube on the both sides. Attention, if the tube has a welding point on the interior side, make sure not to drill there while making the second hole.</translate> | ||
|Step_Picture_00=SolarOSE_G1_1_1.jpg | |Step_Picture_00=SolarOSE_G1_1_1.jpg | ||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
Line 80: | Line 62: | ||
Use a pillar drill of 6 mm, long enough to drill the square tube on both sides (if necessary, it should have at least 60 mm to drill simultaneously the two tubes put one above each other).</translate> | Use a pillar drill of 6 mm, long enough to drill the square tube on both sides (if necessary, it should have at least 60 mm to drill simultaneously the two tubes put one above each other).</translate> | ||
|Step_Picture_00=SolarOSE_G1_2_1.jpg | |Step_Picture_00=SolarOSE_G1_2_1.jpg | ||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
|Step_Title=<translate>Assembling all the tubes</translate> | |Step_Title=<translate>Assembling all the tubes</translate> | ||
|Step_Content=<translate>Put all the square tubes on a table: begin with the tubes of 25x25 mm, afterwards put under the tubes of 30x40 mm, assuring that the surface of 40 mm is connected to the extremities of 25x25 mm. Fix them at each angle with a screw of M6 having a length of 60 mm. The tubes can be adjusted if the right angle is verified with a protractor. If the second screw does not enter in the two tubes, the hole alignment should be adjusted by passing the stand alone drill through. Repeat the procedure to all angles in order to complete the fixation.</translate> | |Step_Content=<translate>Put all the square tubes on a table: begin with the tubes of 25x25 mm, afterwards put under the tubes of 30x40 mm, assuring that the surface of 40 mm is connected to the extremities of 25x25 mm. Fix them at each angle with a screw of M6 having a length of 60 mm. The tubes can be adjusted if the right angle is verified with a protractor. If the second screw does not enter in the two tubes, the hole alignment should be adjusted by passing the stand alone drill through. Repeat the procedure to all angles in order to complete the fixation.</translate> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
Line 100: | Line 71: | ||
|Step_Content=<translate>Cut with the laser cutter 20 wood support pieces for the motors and 40 wood support pieces for the axes of the mirror. It is necessary 40 pieces in order to assure one piece to each extremity.</translate> | |Step_Content=<translate>Cut with the laser cutter 20 wood support pieces for the motors and 40 wood support pieces for the axes of the mirror. It is necessary 40 pieces in order to assure one piece to each extremity.</translate> | ||
|Step_Picture_00=SolarOSE_G1_3_1.jpg | |Step_Picture_00=SolarOSE_G1_3_1.jpg | ||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
|Step_Title=<translate>Fix the wood support pieces on the frame</translate> | |Step_Title=<translate>Fix the wood support pieces on the frame</translate> | ||
|Step_Content=<translate>Fix with 2 screws the wood support pieces for the motor on the tube, exterior part and the wood support pieces for the axes of the mirror as indicated on the 3D view. The motor and the axis of the mirror are fixed under the tube, so their wood support pieces should overpass above.</translate> | |Step_Content=<translate>Fix with 2 screws the wood support pieces for the motor on the tube, exterior part and the wood support pieces for the axes of the mirror as indicated on the 3D view. The motor and the axis of the mirror are fixed under the tube, so their wood support pieces should overpass above.</translate> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Tuto Step}} | {{ {{tntn|Tuto Step}} | ||
Line 122: | Line 82: | ||
They are assembled on tubes of 50x50 mm, cut and drilled as indicated in the 3D model.</translate> | They are assembled on tubes of 50x50 mm, cut and drilled as indicated in the 3D model.</translate> | ||
|Step_Picture_00=SolarOSE_G1_4_1.jpg | |Step_Picture_00=SolarOSE_G1_4_1.jpg | ||
− | |||
− | |||
− | |||
− | |||
− | |||
}} | }} | ||
{{ {{tntn|Notes}} | {{ {{tntn|Notes}} | ||
− | |Notes=[[SolarOSE_-_Solar_concentrator_for_steam_generation|Project page]] | + | |Notes=<translate>[[SolarOSE_-_Solar_concentrator_for_steam_generation|Project page]] |
− | Next step: [[SolarOSE_-_Guide_2:_Mirror_facets]] | + | Next step: [[SolarOSE_-_Guide_2:_Mirror_facets]]</translate> |
}} | }} | ||
+ | {{ {{tntn|Tuto Status}} | ||
+ | |Complete=Published | ||
+ | }} | ||
+ | {{Separator}} |
Author OSE France | Last edit 9/12/2019 by Clementflipo
SolarOSE_G1_4_1.jpg en none Creation 0
Use the grinder to cut at the length of 2130 mm the two main squared tubes and at the length of 1430 mm the 2 square tubes for the support.
Goal The two square tubes for the support have to be drilled with two holes every 143 mm. The position of the holes assures that the mirrors are parallel. It is important to work precisely so that the mirrors reflect the light in the same line.
How to? Print the template. Use the available drawing file which is composed of two parts; it is enough to put the two parts one next to each other. Put the template on the square tube and make sure that the paper is fixed to the edges and the extremities of the tube. Fix the template with the adhesive tape. Attention: if the square tube is welded from the interior on one face, this face has to be drilled first. Otherwise, if the opposite face is drilled, the drill will be deviated near the welding point.
Punch precisely the holes marked on the template with a needle and a hammer.
Use a pillar drill with a diameter of 6 mm. The drill should be long enough to drill the square tube on the both sides. Attention, if the tube has a welding point on the interior side, make sure not to drill there while making the second hole.
Goal The goal is to drill two holes on each extremity of the four tubes; the holes help to maintain the square shape.
How to? Scratch the holes position on the tubes as indicated in the 3D model. The two holes are placed at 10 mm and at 30 mm on the tube having a width of 40 mm and they are centered at 12.5 mm on the tube having a width of 25 mm. With these holes, the tubes are fixed on their extremities.
Use a pillar drill of 6 mm, long enough to drill the square tube on both sides (if necessary, it should have at least 60 mm to drill simultaneously the two tubes put one above each other).
Put all the square tubes on a table: begin with the tubes of 25x25 mm, afterwards put under the tubes of 30x40 mm, assuring that the surface of 40 mm is connected to the extremities of 25x25 mm. Fix them at each angle with a screw of M6 having a length of 60 mm. The tubes can be adjusted if the right angle is verified with a protractor. If the second screw does not enter in the two tubes, the hole alignment should be adjusted by passing the stand alone drill through. Repeat the procedure to all angles in order to complete the fixation.
Cut with the laser cutter 20 wood support pieces for the motors and 40 wood support pieces for the axes of the mirror. It is necessary 40 pieces in order to assure one piece to each extremity.
Fix with 2 screws the wood support pieces for the motor on the tube, exterior part and the wood support pieces for the axes of the mirror as indicated on the 3D view. The motor and the axis of the mirror are fixed under the tube, so their wood support pieces should overpass above.
Two frames are constructed as indicated in the steps 1 to 6.
They are assembled on tubes of 50x50 mm, cut and drilled as indicated in the 3D model.
Project page Next step: SolarOSE_-_Guide_2:_Mirror_facets
Published
You entered an invalid page name, with one or many of the following characters :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #