MicroHouse

MicroHouse is a high-performance, one-bed house type, designed using the WikiHouse building system. It uses WikiHouse products WREN and SPARROW. It has been designed primarily for use in the UK, but could also be adapted for other countries and regions. The home can be largely self-assembled, and costs around £37,000 GBP to produce. Our files are also intended as starter files for architects, designers, engineers and others interested in getting to know the WikiHouse WREN system.

Auteur WikiHouse | Dernière modification 9/12/2019 par Clementflipo

Difficulté

Moyen

Durée

5 jour(s)

Catégories

Maison

Coût

37000 GBP (£)

MicroHouse is a high-performance, one-bed house type, designed using the WikiHouse building system. It uses WikiHouse products WREN and SPARROW. It has been designed primarily for use in the UK, but could also be adapted for other countries and regions. The home can be largely self-assembled, and costs around £37,000 GBP to produce. Our files are also intended as starter files for architects, designers, engineers and others interested in getting to know the WikiHouse WREN system.

Difficulté

Moyen

Durée

5 jour(s)

Catégories

Maison

Coût

37000 GBP (£)

Licence : Attribution-ShareAlike (CC BY-SA)

MicroHouse_Final.jpg en en Creation 0

Introduction

Please scan all your site notes from the process and edit this tutorial to share them with us.

By using this tutorial you agree to the following terms and conditions.

Matériaux

Check the list of supplies you will need in the file MicroHouse Pilot Engine.xlsx. We also provide the names of suggested suppliers but you are free to buy them anywhere else.

Buy locally 18mm plywood in the standard sheet size of 2440mm x 1220mm (8' x 4')

All construction is dangerous. Always wear hard hards, eye protection, ear protection (malleting gets very loud), gloves, high visibility outfits and steel-capped boots. Where working at height is required, use a harness. Establish a ‘safety first’ culture on site, and encourage the continuous identification of hazards.

Outils

For this assembly you will need:

1 x Step ladder (8ft or 10ft) 5 x Step Ups
1 x Mobile scaffolding
1 x Roof ladder
1 x Large tarpaulin rain cover
1 x Marquee (or other enclosed area) to store parts dry and off the ground. 5+ Mallets
2+ Electric screwdrivers with as many spare batteries as possible
1x Electric drill
1x Electric jigsaw
1x hand screw driver (to use as a lever)
1 x Staple gun
2 x Scissors / knife
4 x Large clamps
1 x Plasterboard filler trowel

https://github.com/wikihouseproject/Microhouse/

Étape 1 - Cut the parts

Download on our Github repo the set of milling drawings which can be used by CNC cutter to fabricate the house parts.

Cut the part by a CNC mill using locally bought material. This is 18mm plywood, in the standard sheet size of 2440mm x 1220mm (8' x 4')

Each component can be combined or adapted to form a structure which responds to an individual site or set of needs.

Étape 2 - Foundations

Site preparation Make sure passers-by can’t wander onto your site. It’s also a good idea to warn neighbours in advance that there’ll be some noise, especially from malleting.

Almost any foundation type can be used, provided it can support the joist ‘rails’. The rails must be level and parallel (+/- 5mm). Consult a builder or engineer to assess design and specification of foundations.

Floor area 37.5m2

Étape 3 - Foundations

1. Service location jig CNC manufactured to set precise location for service connections.

2. Trench Foundations Depth of concrete will vary.

3. Bolts Fixing into concrete, ready to receive brackets.

4. DPM Trap two strips of damp proof membrane (DPM) beneath joist rail, with about 200mm sticking out to outer side

5. End walls Concrete or brick wall with ventilation holes.

Étape 4 - Deck

Use timber (for example, the battens) to create a temporary assembly deck. The deck needs to be stable and not bounce when malleted.

Étape 5 - Section assembly

Set out the parts for each section onto the ground, assembly is like a jigsaw.

Étape 6 - Pledge the layers

Pledge together the two layers to form a single section.

Étape 7 - Skis

Fit skis to underside of each superbox frame before raising.

Étape 8 - Stand the sections up vertically

Stand the sections up vertically, positioning them at 600mm intervals.

Fit the connector pieces into the slots in the section. These should be staggered alternately. Use the mallet provided on the milling sheets to hammer these tightly into place.

Étape 9 -

Étape 10 - Cladding panels

Fit the internal and external cladding panels onto the structure. Internally these usually need to be screwed into place.

Étape 11 - Fixing down

Use bolts and/or large screws, depending on the foundation type. Always consult an engineer or building professional, especially to ensure footings are adequate. During high winds, uplift can be very strong.

Heavy duty brackets Onto rail joist

Étape 12 - Insulation

Drainage

Install underfloor soil pipe plus shower and washing machine drain before surrounding with insulation. You may wish to skip all but the two end bays for now.

Layers

Wherever rolled insulation is used, two layers will be required:

100mm + 150mm = 250mm

Étape 13 -

Étape 14 -

Étape 15 -

Étape 16 - Wrap and Openings

Wrap

Work upwards, giving at least 200mm overlap. Ensure all folds are double wrapped and ‘weathered’ so water will run downwards.

Openings Don’t cut openings until you are ready to fit windows, unless you need them for access. This way, the chassis is protected from rain during the build.

Étape 17 -

Use airtight tape (Tescon or similar)

1. Seals Around all service penetrations

Vapour barrier

Use a tough vapour barrier (eg Intello) that can be stapled directly. If using a thinner vapour barrier, all staples will need to be over-patched with tape.

Étape 18 - Windows

1. Flashing tape

Around entire opening before fitting window

Window unit

Install as per manufacturer’s instructions. In most cases, front face should be flush with chassis.

Expanding tape

Fit to windows seconds before installing unit and allow to expand. Pinch corners slightly to ensure no corner gaps. Check complete seal around unit. If possible add additional flashing tape to exterior. It is impossible to be too thorough. Wind will drive rain into even the smallest crack.