(set pageLanguageSource property) |
(update property name) |
||
| (Une révision intermédiaire par un autre utilisateur non affichée) | |||
| Ligne 1 : | Ligne 1 : | ||
| − | {{ | + | {{Tuto Details |
|SourceLanguage=none | |SourceLanguage=none | ||
|Language=en | |Language=en | ||
| Ligne 14 : | Ligne 14 : | ||
|Main_Picture=Lampe en bois ciment Final.jpg | |Main_Picture=Lampe en bois ciment Final.jpg | ||
}} | }} | ||
| − | {{ | + | {{Introduction |
|Introduction=<translate><!--T:1--> While leafing through decoration magazines, I came up with the idea of that simple desk lamp made of wood and concrete. Is this a good introduction to you?</translate> | |Introduction=<translate><!--T:1--> While leafing through decoration magazines, I came up with the idea of that simple desk lamp made of wood and concrete. Is this a good introduction to you?</translate> | ||
}} | }} | ||
| − | {{ | + | {{Materials |
|Material=<translate><!--T:2--> | |Material=<translate><!--T:2--> | ||
* Concrete | * Concrete | ||
| Ligne 34 : | Ligne 34 : | ||
}} | }} | ||
{{Separator}} | {{Separator}} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:3--> Take measures</translate> | |Step_Title=<translate><!--T:3--> Take measures</translate> | ||
|Step_Content=<translate><!--T:4--> Put a mark on the batten, to cut it in 2 battens of 44cm length</translate> | |Step_Content=<translate><!--T:4--> Put a mark on the batten, to cut it in 2 battens of 44cm length</translate> | ||
| Ligne 44 : | Ligne 44 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:5--> cut the battens</translate> | |Step_Title=<translate><!--T:5--> cut the battens</translate> | ||
|Step_Content=<translate><!--T:6--> | |Step_Content=<translate><!--T:6--> | ||
| Ligne 58 : | Ligne 58 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:8--> mark position of the holes</translate> | |Step_Title=<translate><!--T:8--> mark position of the holes</translate> | ||
|Step_Content=<translate><!--T:9--> | |Step_Content=<translate><!--T:9--> | ||
| Ligne 75 : | Ligne 75 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:11--> Drill the holes</translate> | |Step_Title=<translate><!--T:11--> Drill the holes</translate> | ||
|Step_Content=<translate><!--T:12--> Get your drill in action !</translate> | |Step_Content=<translate><!--T:12--> Get your drill in action !</translate> | ||
| Ligne 85 : | Ligne 85 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:13--> cut the screw</translate> | |Step_Title=<translate><!--T:13--> cut the screw</translate> | ||
|Step_Content=<translate><!--T:14--> Cut the screw at good size : to pass throw the 2 battens plus the nuts</translate> | |Step_Content=<translate><!--T:14--> Cut the screw at good size : to pass throw the 2 battens plus the nuts</translate> | ||
| Ligne 95 : | Ligne 95 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:15--> Add iron wire</translate> | |Step_Title=<translate><!--T:15--> Add iron wire</translate> | ||
|Step_Content=<translate><!--T:16--> pass an iron wire into the bottom holes, and do a structure with it to get a good link between the wood and the concrete.</translate> | |Step_Content=<translate><!--T:16--> pass an iron wire into the bottom holes, and do a structure with it to get a good link between the wood and the concrete.</translate> | ||
| Ligne 105 : | Ligne 105 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:17--> prepare the mould</translate> | |Step_Title=<translate><!--T:17--> prepare the mould</translate> | ||
|Step_Content=<translate><!--T:18--> Prepare a box for the mould, and fix the batten in it with a screw.This screw will be removed after the concrete get solid.</translate> | |Step_Content=<translate><!--T:18--> Prepare a box for the mould, and fix the batten in it with a screw.This screw will be removed after the concrete get solid.</translate> | ||
| Ligne 115 : | Ligne 115 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:19--> prepare the concrete</translate> | |Step_Title=<translate><!--T:19--> prepare the concrete</translate> | ||
|Step_Picture_00=Lampe_en_bois_ciment_09_1.jpg | |Step_Picture_00=Lampe_en_bois_ciment_09_1.jpg | ||
| Ligne 124 : | Ligne 124 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:20--> Cast the concrete</translate> | |Step_Title=<translate><!--T:20--> Cast the concrete</translate> | ||
|Step_Content=<translate><!--T:21--> Tap the box to remove air bubbles, and let the concrete get solid.</translate> | |Step_Content=<translate><!--T:21--> Tap the box to remove air bubbles, and let the concrete get solid.</translate> | ||
| Ligne 134 : | Ligne 134 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:22--> Sand the concrete</translate> | |Step_Title=<translate><!--T:22--> Sand the concrete</translate> | ||
|Step_Content=<translate><!--T:23--> Once the concrete is solid, sand it to get beautiful surface</translate> | |Step_Content=<translate><!--T:23--> Once the concrete is solid, sand it to get beautiful surface</translate> | ||
| Ligne 144 : | Ligne 144 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:24--> assemble the light</translate> | |Step_Title=<translate><!--T:24--> assemble the light</translate> | ||
|Step_Content=<translate><!--T:25--> screw the battens together</translate> | |Step_Content=<translate><!--T:25--> screw the battens together</translate> | ||
| Ligne 154 : | Ligne 154 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:26--> get the power</translate> | |Step_Title=<translate><!--T:26--> get the power</translate> | ||
|Step_Content=<translate><!--T:27--> pass the electric cable throw the holes</translate> | |Step_Content=<translate><!--T:27--> pass the electric cable throw the holes</translate> | ||
| Ligne 164 : | Ligne 164 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Tuto Step |
|Step_Title=<translate><!--T:28--> add the bulb</translate> | |Step_Title=<translate><!--T:28--> add the bulb</translate> | ||
|Step_Content=<translate><!--T:29--> Add the bulb the finish your desk lamp</translate> | |Step_Content=<translate><!--T:29--> Add the bulb the finish your desk lamp</translate> | ||
| Ligne 174 : | Ligne 174 : | ||
|Step_Picture_05=No-image-yet.jpg | |Step_Picture_05=No-image-yet.jpg | ||
}} | }} | ||
| − | {{ | + | {{Notes|}} |
{{Tuto_Status | {{Tuto_Status | ||
| − | |Complete= | + | |Complete=Published |
}} | }} | ||
Version actuelle datée du 9 décembre 2019 à 11:30
Hi! I am Clément, co-founder of Wikifab ! I have created this tutorial to let you learn by yourself how to use Wikifab. This tutorial is your sand box! Everybody can modify it! Don't be shy, clic on the "Edit" link in the top tabs and make your first contribution today!
Difficulté
Facile
Durée
2 heure(s)
Catégories
Décoration, Mobilier
Coût
20 USD ($)
Sommaire
- 1 Introduction
- 2 Étape 1 - Take measures
- 3 Étape 2 - cut the battens
- 4 Étape 3 - mark position of the holes
- 5 Étape 4 - Drill the holes
- 6 Étape 5 - cut the screw
- 7 Étape 6 - Add iron wire
- 8 Étape 7 - prepare the mould
- 9 Étape 8 - prepare the concrete
- 10 Étape 9 - Cast the concrete
- 11 Étape 10 - Sand the concrete
- 12 Étape 11 - assemble the light
- 13 Étape 12 - get the power
- 14 Étape 13 - add the bulb
- 15 Commentaires
Introduction
While leafing through decoration magazines, I came up with the idea of that simple desk lamp made of wood and concrete. Is this a good introduction to you?
Matériaux
- Concrete
- Woods
Outils
- Saw
- Drill
- Light
Étape 1 - Take measures
Put a mark on the batten, to cut it in 2 battens of 44cm length
Étape 2 - cut the battens
Cut the battens !
For better design, you can cut the top batten with a little slant on the top end.
Étape 3 - mark position of the holes
Mark the position of the holes.
We need :
- one hole in each batten to fix them with screw
- some holes to pass the cable
- one holes at the bottom, which will be within the concrete
Étape 4 - Drill the holes
Get your drill in action !
Étape 5 - cut the screw
Cut the screw at good size : to pass throw the 2 battens plus the nuts
Étape 6 - Add iron wire
pass an iron wire into the bottom holes, and do a structure with it to get a good link between the wood and the concrete.
Étape 7 - prepare the mould
Prepare a box for the mould, and fix the batten in it with a screw.This screw will be removed after the concrete get solid.
Étape 8 - prepare the concrete
Étape 9 - Cast the concrete
Tap the box to remove air bubbles, and let the concrete get solid.
Étape 10 - Sand the concrete
Once the concrete is solid, sand it to get beautiful surface
Étape 11 - assemble the light
screw the battens together
Étape 12 - get the power
pass the electric cable throw the holes
Étape 13 - add the bulb
Add the bulb the finish your desk lamp
Published
Français
English
Deutsch
Español
Italiano
Português